What to do if Dolmar Brush Cutter engine stops soon?
If your Dolmar Brush Cutter's engine stops soon after starting, it could be due to: * Insufficient warm-up. Perform a warm-up operation. * Choke lever is set to “CLOSE” although engine is warmed up. Set it to “OPEN”. * Clogged fuel filter. Clean the filter. * Contaminated or clogged air cleaner. Clean the air cleaner.
What to do if Dolmar Brush Cutter main unit vibrates abnormally?
If the main unit of your Dolmar Brush Cutter vibrates abnormally, check for the following: * A broken, bent, or worn cutter blade. Replace the cutter blade. * A loosened cutter blade-tightening nut. Tighten it securely. * A shifted convex part of cutter blade and cutter blade support fitting. Attach them securely.
What to do if Dolmar Brush Cutter blade does not rotate?
If the cutter blade of your Dolmar Brush Cutter does not rotate, consider these possible causes: * Loosened cutter blade-tightening nut. Tighten the nut securely. * Twigs caught by cutter blade or dispersion- preventing cover. Remove any foreign matter.
What to do if Dolmar MS-245.4 C engine does not stop?
If the engine of your Dolmar Brush Cutter does not stop, check for a detached connector and attach it securely.
What to do if Dolmar Brush Cutter blade does not stop immediately?
If the cutter blade on your Dolmar Brush Cutter does not stop immediately, it may be due to: * High idling rotation. Adjust it. * Detached throttle wire. Attach it securely.
What to do if Dolmar MS-245.4 C engine stops soon after starting?
If your Dolmar Brush Cutter engine stops shortly after starting, it might not be sufficiently warmed up, so perform the warm-up operation. Another cause could be the choke lever being set to “CLOSE” when the engine is warm; set it to “OPEN”. Also, check for a clogged fuel filter (clean it) or a contaminated or clogged air cleaner (clean it). If the problem persists, the carburetor or drive system may be abnormal, requiring professional inspection and maintenance.
How to fix abnormal vibration of Dolmar Brush Cutter?
Abnormal vibration in your Dolmar Brush Cutter can be caused by several issues. Check for a broken, bent, or worn cutter blade and replace it if necessary. Ensure the cutter blade-tightening nut is securely tightened. Also, verify that the convex part of the cutter blade and cutter blade support fitting are securely attached. If the vibration persists, the drive system may be abnormal, requiring professional inspection and maintenance.
Why Dolmar Brush Cutter engine does not start?
The Dolmar Brush Cutter engine might fail to start due to several reasons: * Failure to operate primer pump. Push it 7 to 10 times. * Low pulling speed of starter rope. Pull it strongly. * Lack of fuel. Add fuel. * Clogged fuel filter. Clean it. * Broken fuel tube. Straighten it. * Deteriorated fuel. Replace it with new fuel, as deteriorated fuel makes starting more difficult (recommended replacement: 1 month). * Excessive suction of fuel. Set throttle lever from medium speed to high speed, and pull starter handle until engine starts. Once engine starts, cutter blade starts rotating, so pay full attention to cutter blade. If engine will not start still, remove spark plug, make electrode dry, and reassemble them as they originally are. Then, start as specified. * Detached ...
General advice for safe operation and user responsibilities.
Details essential PPE for safe operation.
Outlines pre-operation checks and safety procedures.
Safe practices for handling fuel, including precautions.
Explanation of uncontrolled kickback and its causes.
Advice to avoid kickbacks during operation.
Procedure for checking and refilling engine oil.
Procedure for checking and replacing engine oil.
Causes and remedies for engine not starting, stopping, or poor performance.
Causes and remedies for cutter blade not rotating or stopping.
Causes and remedies for vibration, stopping issues, and safety concerns.
Lists scheduled maintenance procedures and their intervals.
General| Engine Type | 2-stroke |
|---|---|
| Engine Displacement | 45.6 cm³ |
| Shaft Type | Straight |
| Fuel Tank Capacity | 0.7 L |
| Cutting System | Nylon line |
To Next Page