EasyManua.ls Logo

Dolmar PC-6412 S - User Manual

Dolmar PC-6412 S
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Important:
Read this instruction manual carefully before putting the Power Cut into operation and strictly observe the
safety regulations!
Keep this instruction manual!
Instruction Manual
PC-6412 S
PC-6414 S
PC-7312 S
PC-7314 S
PC-8114
PC-8116
http://www.dolmar.com

Table of Contents

Questions and Answers

  • J
    Jennifer GarciaAug 1, 2025
    Why does my Dolmar Cutter engine not start?
    • S
      stephen77Aug 1, 2025
      If your Dolmar Cutter engine doesn't start or starts with difficulty, it could be due to a malfunction in the fuel supply system, compression system, or a mechanical issue. Other potential causes include the STOP switch being on, a fault or short-circuit in the wiring, a defective plug cap or spark plug, an incorrect choke position, a defective carburetor, a dirty suction head, a bent or interrupted fuel line. Additionally, a defective cylinder base packing ring, radial shaft packings, cylinder or piston rings, or a spark plug that doesn't seal could be the cause. Finally, a broken spring in the starter or broken parts inside the engine could be responsible.
  • H
    Hunter BakerAug 8, 2025
    What to do if Dolmar PC-6412 S Cutter engine starts, but dies immediately?
    • M
      Ms. Tina RobinsonAug 8, 2025
      If your Dolmar Cutter engine starts but immediately dies, it could be due to an incorrect idling adjustment, a dirty suction head or carburetor. Other potential causes include a defective tank venting system, an interrupted fuel line, a defective cable, a defective STOP switch, or a dirty decompression valve.
  • B
    Brett HarrisAug 16, 2025
    Why does my Dolmar PC-6412 S Cutter have insufficient power?
    • E
      Eric SantanaAug 16, 2025
      If your Dolmar Cutter is showing insufficient power, it might be caused by a dirty air filter, incorrect carburetor adjustment, or a clogged exhaust channel in the cylinder.
  • M
    Marcus JohnsonAug 25, 2025
    Why does my Dolmar Cutter have warm start difficulties?
    • G
      Gregory SimsAug 25, 2025
      Warm start difficulties with your Dolmar Cutter can be caused by wrong carburetor adjustment.

Summary

Delivery Inventory

Symbols

Safety Precautions

Intended Use

Specifies the correct and intended applications for the Power Cut machine.

General Precautions

Outlines fundamental safety rules and operator responsibilities for safe operation.

Protective Equipment

Details the mandatory personal protective equipment (PPE) required for safe operation.

Fuels; Refuelling

Putting into Operation

Steps and safety checks before starting and operating the Power Cut.

Cutoff Discs

Kickback and Lock-in

Working Behavior; Method of Working

Describes proper techniques and work practices for efficient and safe operation.

Cutting Metals

Cutting Masonry and Concrete

Transport and Storage

Maintenance

First Aid

Information and procedures for providing immediate first aid in case of an accident.

Disposal and Environmental Protection

Guidelines for environmentally responsible disposal of parts and the unit.

Technical Data

Denomination of Components

Putting into Operation

Mounting the Cutting Disc

Detailed instructions for safely attaching the cutting disc to the machine.

Tightening the V-belt; Checking V-belt Tension

Fuels

Refuelling

Starting the Engine

Cold-starting

Specific steps for starting the engine from a cold state.

Warm-starting

Stopping the Engine

Adjusting the Carburetor

Maintenance

Changing the V-belt

Step-by-step guide for replacing the V-belt on the Power Cut.

Cleaning the Protection Hood

Cleaning; Changing the Air Filter

Air Filter Component Maintenance

Details on cleaning and replacing pre-filters, inner filters, and air filter inserts.

Replacing the Spark Plug

Checking the Ignition Spark

Replacing the Suction Head

Replacing the Starter Cable

Replacing the Return Spring

Cutting Attachment in Central; Side Position

Repositioning the Cutting Attachment

Special Accessories

Diamond Cutting Discs

Description of diamond cutting discs for various materials.

Guide Trolley

Information on the guide trolley for straight and easier cutting.

Water Tank

Details about the water tank accessory for wet cutting applications.

Mains;Pressure Water System

Description of the water system accessory for wet cutting.

Instructions for Periodic Maintenance

Service, Spare Parts and Guarantee

Troubleshooting

Extract from the Spare Parts List

Dolmar PC-6412 S Specifications

General IconGeneral
Engine Type2-stroke
Displacement64 cm³
Chain Pitch3/8"
Chain Gauge1.5 mm
Cutting Diameter40 cm (16")

Related product manuals