Dorma PROSECURE EASY MOTION STEREO User Manual

PROSECURE EASY MOTION STEREO
—
WN 058107 45532, 09/14
Sensor for approach detection at industrial doors
In order to satisfy the safety requirements specified
in EN60950-1, the sensor must be operated from an
SELV supply where the output is limited to 100 W. The
output can be limited using a T2.5 A fuse.
Delivery package
1 Sensor
1 Connecting cable with plug
2 Screws for mounting (in the housing)
1 Self-adhesive mounting template
1 Mounting instructions
2 Locking discs for inclination
Elements
 Antenna
 LED (red)
 Potentionmeter
 redetermined breakaway tab Relay switching mode
 Connector
1
2
3
4
5
Components can be damaged by electrostatic energy!
Do not touch any electronic components.
Do not use metal tools.
Preparation
Insert the screwdriver into the
opening provided, carefully lift
the cover and pull forwards to
remove.
Do not open the housing
from the top.
Turning the antenna unit
(to change the antenna cha-
racteristics)
Push apart the tabs on the arms
of the base plate.
Carefully remove the PCB and
locking discs.
Move the locking discs to the
new position on the PCB.
Push apart the tabs on the arms
of the base plate.
Insert the PCB and locking discs
again. The locking discs must
snap into place.
Installation information
• Protect the sensor from rain*.
• Avoid moving objects in the
detection area (fans, plants,
etc.).
• Do not cover the sensor. Mount
the sensor only behind suitable
covers.
• Moving drive components can
affect the sensor.
• Avoid fluorescent lights in the
detection area.
• The installation conditions may
limit the programming options
and the functions of the sensor.
* DORMA recommends
installing a weather
cap for outdoor appli-
cations.
Mounting
Attach the self-adhesive template
and drill according to the hole
pattern.
Guide the cable through the ope-
ning provided.
Fasten the base plate using the
screws (screws are in the hou-
sing).
Antenna characteristics
A wide or narrow detection area can be set by turning the
PCB.
Installation height 2,20 m
Detection area angle 30°
Detection area size Max
wide
(standard)
Width:
Depth:
4.50 m
2.00 m
narrow
(optional)
Width:
Depth:
2.00 m
4.50 m
Connecting the sensor
Connect the pre-assembled sensor
cable to the connector as follows.
 white = GND
 black = 12 - 36 V DC/
12 - 28 V AC
 red = COM
 green = NO / NC
1
2
3
4
Replacing the cover
Attach the cover on the
top and press down until it
snaps into place.
Attach weather cap if
required.
Mounting options
With a tilting detection area that ranges from 10° to 360°,
wall or ceiling mounting is possible.

Dorma PROSECURE EASY MOTION STEREO Specifications

General

Type	Automatic door operator
Power Supply	230 V AC, 50 Hz
Opening Speed	Adjustable
Closing Speed	Adjustable
Hold-open Time	Adjustable
Safety Features	Obstacle detection

Summary

Antenna Characteristics and Installation

Antenna Characteristics

Sets the wide or narrow detection area by turning the PCB. Includes installation height and detection area angle/size.

Installation Information

Guidance on protecting the sensor from rain, avoiding moving objects, covering the sensor, and fluorescent lights.

Mounting and Connecting

Steps for preparing the unit, mounting the base plate, and connecting the sensor cable.

Mounting Options

Describes wall or ceiling mounting possibilities with a detection area ranging from 10° to 360°.

Adjusting Detection Settings

Adjusting the Inclination Angle

How to adjust the inclination angle from 0° to 90° using integral locking discs in 10° increments.

Setting for an Inclined Detection Area

Tilting the detection field by 15° using supplied locking discs for specific applications like revolving doors.

Detection Area Size

Instructions on changing the size of the detection area using the potentiometer.

Detection Capabilities

Setting detection capabilities via DIP switch, tested by walking in the sensing area.

Direction Detection

Configuring the sensor to trigger by forward movements only or by forward and backward movements.

Cross-Traffic Optimization

Suppressing passers-by to reduce the detection field when cross-traffic is present.

Immunity, Status, and Troubleshooting

Immunity

Minimizes external interferences like rain, vibrations, and reflections with low or high settings.

Relay Contact Switching Mode

Defines the relay contact behavior when detection is active (NO) or passive (NC).

LED Status Display

Details the color indicator (Red LED) and its status during initialization, active detection, or no detection.

Commissioning

Steps for commissioning, including clearing the area, switching on, and testing settings.

Troubleshooting

Lists common faults like door detection, LED issues, or false triggers and their corrective actions.

Technical Data and Compliance

Technical Data

Specifications including operating principle, detection speed, approvals, sensing range, frequency, voltage, power, and dimensions.

EC Conformity

Confirms product compliance with relevant EC directives and harmonized standards for safety and radio equipment.