DOSKO 337-13HC-CE - User Manual

1
Owner’s Manual
Instructions for Operation, Maintenance
Stump and Root Grinder
337-13HC-CE (2962000CE) 357-13HE-CE (2961010CE)
620-20HE-CE (2961020CE) 620-25KE-CE (2961060CE)
Your Dosko grinder is intended for outdoor-use only and can be used to remove many tree stumps and
exposed root systems close to ground level. By moving the blade in sweeping movements laterally over
the top and front of the stump, you can gradually grind it away. Make sure you completely read and
understand this manual before using the grinder for the first time.
WARNING
READ and UNDERSTAND this manual completely before using the grinder! Failure to properly operate,
and maintain this grinder could result in serious injury or death to the operator or bystanders.
All machines have hazards associated with their operation. This stump grinder has certain special hazards,
which you must be aware of. As an operator or owner you have a duty to be aware of these hazards and know
preventive measures to take to avoid them. When reading this manual pay particular attention to avoiding these
hazards.
In particular, be aware of the following:
 Know location of buried electrical and other utility lines.
 Do not allow children or untrained adults to operate.
 Wear eye protection and other personal protection against flying rocks and debris.
 Check that cutter wheel teeth are secured, sharp and not missing.
 Do not operate if operator presence bar fails to stop engine upon release.
 Make sure no children or bystanders are within 23 meters of stump grinding operation.
 Protect cars, windows and other objects within 23 meters from flying debris.
 Be prepared for machine “kickback” when initially contacting the stump.
 Be aware of potential for carbon monoxide (CO) poisoning.
 Prevent fires/explosions from fueling.
 Do not attempt to perform adjustments, declog or clean unit while engine is running.
 Avoid burns from engine or hot exhaust.
 Avoid using in wet or icy conditions where falls may occur.
Details about these hazards are found throughout the manual and are summarized at the end of the manual under
“Important Safety Information.”
STOP!
ADD ENGINE OIL, FUEL & BATTERY: Your stump grinder comes fully assembled and requires only that you add
engine oil to crankcase, fuel to tank, and a battery.
INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged. See the “Receiving
Your Unit” section for instructions on whom to contact to report missing or damaged parts.
Any Questions, Comments, Problems or Parts Orders
Call your dealer or Dosko Customer Service 1-763-428-2237
MODEL NUMBER: 2962000CE, 2961010CE,
2961020CE, 2961060CE
SERIAL NUMBER: _____________
M2961000CEG

Summary

About Your Grinder

Owner;Operator;Renter Training

Instructions for all users to read and understand the manual for safe operation and maintenance.

Rental Companies

Guidance for rental companies to ensure renters have access to and understand the manual.

Engine Instructions

Directs users to the engine's owner's manual for detailed operation and maintenance.

Product Suitability

Outlines the grinder's intended use for tree stumps and defines operating environment.

Warranty Registration

Instructions for filling out and submitting the warranty registration card for future contact.

Safety Decals

Decal Identification and Placement

Identifies key safety decals by reference number, part number, and description.

Decal Maintenance Warning

Emphasizes the importance of keeping safety labels in place and legible.

Receiving

Receiving Your Unit

Instructions for inspecting the grinder upon delivery for missing or damaged components.

Machine Component Identification

Component Diagram and Labels

Provides a labeled diagram of the grinder and a list of component names and reference numbers.

Pre-Start Check List & Procedures

Marking Underground Utilities

Calls for marking utilities 3 days before grinding to avoid underground hazards.

Check Controls

Ensures all guards are in place and the operator presence bar moves freely.

Check Cutting Teeth

Inspects cutting teeth for tightness and sharpness, recommending factory-approved parts.

Check;Add Oil

Details checking and adding engine oil to the crankcase using the dipstick.

Starting the Grinder

Stopping the Engine

Grinding the Stump

Refueling

Storing the Grinder

Maintenance & Repair

Belt Tension Adjustment

Stop-Switch Adjustment

Setting Teeth

Maintenance Schedule

Specifications

Summary of Important Safety Information

General Safety Guidelines

Essential safety practices for operating and servicing the grinder.

Prohibitions Against Modifications

Warns against modifying the grinder, which can create hazards and void warranty.

Safety Before Use

Key safety checks and considerations before starting the grinder.

Getting Ready for Operation

Important steps for preparing the work area and operating safely outdoors.

Personal Protective Equipment

Gasoline Safety

Safety During Use

Safety After Use

Safety Inspection and Maintenance

Special Safety Information on Static Electricity

Exploded View

Parts List

Wiring Diagram 337-13 HC-CE, 357-13 HE-CE, 620-20 HE-CE

Wiring Diagram 620-25 KE-CE

Limited Warranty Policy

Warranty Coverage Details

Outlines the warranty periods for different components and conditions of coverage.

DOSKO 337-13HC-CE Specifications

General

Brand	DOSKO
Model	337-13HC-CE
Category	Grinder
Language	English