What to do if Dräger Safety Equipment camera is frozen?
If your Dräger Safety Equipment camera is completely non-functional, for example, if you have a frozen image or the camera does not respond to the keys you press, it may be due to a software malfunction. To resolve this, press the ON/OFF button for 10 seconds, then switch the camera back on.
Why won't my Dräger Safety Equipment camera turn on?
If your Dräger Safety Equipment camera won't switch on, it could be due to an empty battery. Recharge the battery. Alternatively, the battery screws might be loose, so try tightening them.
What to do if Dräger Safety Equipment charging cradle LEDs indicate an error?
If the charging cradle LEDs indicate an error during charging of your Dräger Safety Equipment, it could be due to dirty contacts on the battery or the charging cradle. Clean the contacts with a lint-free cloth. Another cause might be that the battery is too cold or too hot. Leave the battery in the charger and place the charger in an area with an ambient temperature between 10 and 35 °C (50 °F and 95 °F). The charger will charge the battery once the temperature inside the charger is correct. It may take significantly more than an hour before the internal temperature reaches the permissible range again and charging resumes since the temperature is measured directly on the Li-ion cells.
How to troubleshoot Dräger Safety Equipment charging cradle LED errors?
If the charging cradle LEDs on your Dräger Safety Equipment indicate an error or do not light up, several issues could be the cause. Here are a few things to check: 1. Ensure the crawling plate is correctly positioned and sufficiently fastened by retightening the screw. 2. Verify and correct the position of the carrying strap. 3. Remove any foreign objects from under the crawling plate or in the charging cradle. 4. Place the charging cradle on a level surface. 5. Check the operation of the power supply unit and/or vehicle connection cable to ensure supply voltage is present.
Why is the Dräger Safety Equipment laser pointer weak?
If the laser pointer on your Dräger Safety Equipment is weak or diffused, it is likely due to water droplets or dirt on the laser emission window. Clean the laser emission window to resolve this issue.
What to do if Dräger UCF 9000 Thermal cameras crawling plate is not positioned correctly?
If the crawling plate of your Dräger Thermal camera is not positioned correctly, several factors could be at play. First, ensure the crawling plate is sufficiently fastened in place by retightening the screw. Also, check and correct the position of the carrying strap. Remove any foreign objects from under the crawling plate or in the charging cradle. Finally, ensure the charging cradle is placed on a level surface.
Why is my Dräger Thermal cameras battery not charging?
If your Dräger Thermal camera's battery is not charging, it might be too cold or too hot. Leave the battery in the charger and place the charger in an area with an ambient temperature between 10 and 35 °C (50 °F and 95 °F). The charger will begin charging the battery once the temperature inside the charger is correct.
How to clean Dräger UCF 9000 Thermal cameras battery contacts?
To clean the battery contacts on your Dräger Thermal camera, use a lint-free cloth to wipe the contacts on both the battery and the charging cradle.
Why is my Dräger thermal camera not switching on?
If your Dräger thermal camera is not switching on, it may be due to the following reasons: the battery is empty (recharge the battery) or the battery screws are loose (tighten screws).
What to do if the charging cradle LEDs indicate an error during charging my Dräger thermal camera?
If the charging cradle LEDs indicate an error during the charging process of your Dräger thermal camera, it could be due to dirty contacts on the battery or charging cradle (clean contacts with a lint-free cloth), or the battery being too cold or too hot. In the latter case, leave the battery in the charger and place the charger in an area with an ambient temperature between 10 and 35 °C (50 °F and 95 °F). The charger will charge the battery once the temperature inside the charger is correct. Charging may take significantly more than an hour to resume, as the temperature is measured directly on the Li-ion cells.
Key safety guidelines for product usage and user responsibility.
Explains the meaning of warning, caution, and notice symbols used in the manual.
Introduces the thermal imaging camera models and their visual components.
Explains the camera's operational features, standby function, and connectivity.
Lists and describes various operational modes available for the camera models.
Outlines the primary applications and purposes of the thermal imaging cameras.
Essential operational guidelines, warnings, and recommendations for safe and effective use.
Steps and precautions required before operating the thermal imaging camera.
Operational procedures and functions while the camera is in use.
How to power the device on, put it in standby, and switch it off.
Solutions for issues related to the camera failing to power on.
Steps to resolve issues where the camera is unresponsive or frozen.
Procedures for checking the camera's condition after use and during storage.
General| Battery Life | up to 5 hours |
|---|---|
| Protection Class | IP54 |
| Frame Rate | 50 Hz |
| Focus | Manual focus |
| Accuracy | ±2°C or ±2% of reading |
| Temperature Range | -40°C to +1, 000°C |
| Zoom | Digital zoom |
| Spectral Range | 8 - 14 µm |
| Display | 4.3 inch |
| Thermal Sensitivity | < 0.05 K at 30°C |
To Next Page
