DriSteem Vapor-Logic Installation Manual

Other manuals for DriSteem Vapor-Logic

Installation And Operation Manual112 pages

Installation Instructions & Maintenance Operations Manual40 pages

• A

  Austin CrossSep 3, 2025

  How to troubleshoot a DriSteem Vapor-Logic with no green power light?

  

  Same questionReply

  • R

    Robert MartinSep 4, 2025

    If the green power indicator light on your DriSteem Control Systems is off, check for proper supply voltage to ensure there is control voltage. If voltage is absent, inspect the heater fuses for any opens and check for voltage present at the transformer. Also, verify if the transformer secondary circuit breaker has tripped, check for any wiring shorts, and reset the breaker.

    

    Reply
• K

  Kimberly HughesSep 1, 2025

  How to fix a DriSteem Vapor-Logic Control Systems keypad/display that doesn't energize?

  

  Same questionReply

  • R

    Rebecca GarciaSep 2, 2025

    If the keypad/display on your DriSteem Control Systems does not energize, begin by checking the main fuse, main line safety switches, and heater fuses to ensure supply voltage to the unit is present. Next, verify that there is a proper 24 VAC supply, checking the transformer voltage characteristics and wiring. If voltage is absent, inspect the transformer circuit breaker and reset if needed. Also, check if the humidifier over-temperature thermostat is open and reset the manual switch located above the heater below the terminal cover.

    

    Reply
• M

  Michael LopezSep 1, 2025

  Why is my DriSteem Control Systems unit not performing automatic drain?

  

  Same questionReply

  • J

    Jennifer Cummings MDSep 1, 2025

    If your DriSteem Control Systems unit is not performing the automatic drain sequence, first verify that your humidifier is equipped with an automatic drain system and that it is enabled in the Setup menu. Then, check for a drain fault, a plugged drain valve, or a plugged drain pipe, and clean the drain valve piping if necessary. If the automatic drain sequence is malfunctioning, review the auto drain/flush settings in the Setup menu. Ensure that 24 VAC is present at terminal block P17 (drain) and at the drain valve. If voltage is present but the valve does not open, the automatic drain valve may be defective and require replacement.

    

    Reply
• S

  Stacy LiAug 28, 2025

  How to fix a DriSteem Control Systems read-out that is not auto scrolling?

  

  Same questionReply

  • J

    Jennifer WilliamsAug 28, 2025

    If the read-out is not auto-scrolling on your DriSteem Control Systems, it might be because the digital display is in main or sub-menu format. Press the "MODE" key to return to auto scrolling.

    

    Reply
• A

  Amy CoxAug 27, 2025

  What to do if there is no remote fault indication on DriSteem Vapor-Logic?

  

  Same questionReply

  • G

    George QuinnAug 27, 2025

    If there is no remote fault indication on your DriSteem Control Systems, there are a few things to check: 1. Ensure that field wiring is installed to a remote fault indicator from the VAPOR-LOGIC terminal block J7. 2. Check if the field-supplied remote fault indicator lamp is burned out and replace if necessary. 3. Verify relay continuity (VAPOR-LOGIC terminal J7) for contact closure, as the remote fault VAPOR-LOGIC relay may not be switching.

    

    Reply
• D

  Daniel FullerAug 26, 2025

  What does it mean when the VAPOR-LOGIC red indicator light is on continuously on DriSteem Control Systems?

  

  Same questionReply

  • J

    Joy AlvaradoAug 27, 2025

    If the VAPOR-LOGIC red indicator light is continuously on for DriSteem Control Systems, it may be due to a disruption in the VAPOR-LOGIC microprocessor. Verify proper control cabinet wiring and press the "RESET" button to reset the VAPOR-LOGIC control board.

    

    Reply
• P

  Patrick ChangAug 26, 2025

  Why can't I enter new parameters into the microprocessor through the keypad on DriSteem Vapor-Logic?

  

  Same questionReply

  • F

    Frederick HollowayAug 26, 2025

    If you cannot enter new parameters into the microprocessor through the keypad on your DriSteem Control Systems, ensure that the digital display is not in "AUTO" or main menu format. Press the "MODE" key to enter the main menu, and then press the "ENT" key to access data in the selected main menu item. If new parameters are out of range, press the "CLR" key to start over and enter parameters within the acceptable range.

    

    Reply
• J

  jorge68Aug 25, 2025

  How to troubleshoot a VAPOR-LOGIC red indicator light that is off on DriSteem Control Systems?

  

  Same questionReply

  • N

    Nicole SotoAug 25, 2025

    If the VAPOR-LOGIC red indicator light is off on your DriSteem Control Systems, it could be due to several reasons: * First, check for proper supply voltage. * Second, inspect the heater fuses for voltage at the transformer. * Third, see if the transformer secondary circuit breaker has tripped; if so, check for wiring shorts and reset the breaker. * Finally, verify proper control cabinet wiring and try pressing the "RESET" button to reset the VAPOR-LOGIC control board in case of a microprocessor logic disruption.

    

    Reply

DriSteem Vapor-Logic Specifications

General

Control Type	Microprocessor-based
Display	LCD
Remote Monitoring	Yes
Operating Temperature	32°F to 122°F (0°C to 50°C)
Enclosure Rating	NEMA 1 (IP20)
Communication Protocol	Modbus RTU

Related product manuals

DriSteem VAPOR-LOGIC 3

75 pages

DriSteem Vapor-logic 4

104 pages