DT Research DT315CT User Manual

DT315CT/ DT315CT-MD
ENGLISH
4
5
ENGLISH
OPERATION
Powering ON and OFF
To acvate the DT315CT/ DT315CT-MD, push and quickly release the Power Buon. The
display will come on in a few seconds. To put the DT315CT/ DT315CT-MD in Standby
mode, push and quickly release the Power Buon. To turn the DT315CT/ DT315CT-MD
off for extended storage, power off safely using any soware funcon that
“
shuts down
computer
”
provided in the soware opera
ng system.
NOTE:
The baery packs shipped with your tablet may be low in power
—
please use
the AC-DC adapter with the DT315CT/ DT315CT-MD when seng up for the
first me to fully charge the internal baery pack. You may charge the external
baery pack with it aached to the DT315CT/ DT315CT-MD, or with the
oponal external baery charger kit.
NOTE:
When the baery pack(s) is (are) charging, the blue-
colored Baery LED should
blink slowly. If plugging in the AC-DC adapter does not trigger this blinking
acvity and the LED stays dark, the baery pack(s) may have been drained
substanally. Try unplugging/ replugging the AC-DC adapter to the DT315CT/
DT315CT-MD a few mes to acvate the charging process.
NOTE:
To conserve power, use (push and quick release) the Power Buon to put the
tablet in
“
St
andby
”
mode while not in use. Pushing briefly on the same buon
will wake up the system within seconds.
NOTE:
Avoid using the Power Buon (
“
hold 4+ seconds
”
feature) to turn off the
tablet
—
this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface will
be di
splayed aer a launch sequence of several seconds. The wireless LAN connecon
may take 10-15 seconds to be established.
Configuring the Mobile Tablet
The DT315CT/ DT315CT-MD may be configured using the ulies and methods dictated
by the soware operang system. The DT315CT/ DT315CT-MD should be configurable
for various properes such as user profiles, network features, and several system
elements.
Calibraon
The touch display for the DT315CT/ DT315CT-MD is calibrated before shipping. In the
event that the calibraon has been modified or is unsasfactory, the respecve calibra-
on rounes (e.g., PenMount (PM)) to calibrate the touch interface may be used.
Wireless Networking
Wireless LAN
The DT315CT/ DT315CT-MD is oen delivered with an embedded (user-inaccessible)
802.11a/b/g/n WLAN adapter equippe
d with a hidden custom antenna.
T
• hrough the support of typical WLAN adapters, the DT315CT/ DT315CT-MD should
be able to detect all 802.11 access points in the vicinity for you to select the access
point of your choice for connecon.
T
• he SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT315CT/ DT315CT-
MD and the access points have to match. The SSID is case-sensive and it is
recommended t
hat you enable WEP/WPA/WPA2 encrypon (or advanced alterna-
ves) for secure access.
W
• hen WEP/WPA/WPA2 is enabled, you may need to consult your network admin-
istrator or your networking equipment literature to properly configure associated
sengs such as Authencaon mode, etc.
R
• efer to the access point operang manuals for seng up the 802.11 access points.

DT Research DT315CT Specifications

General

Brand	DT Research
Model	DT315CT
Category	Tablet
Language	English