What to do if my DT SWISS Bicycle Accessories wheel has lateral or radial runout?
If your DT SWISS Bicycle Accessories wheel has lateral or radial runout, it is likely due to loose spokes or an external force. You should true the wheel and check the spoke tension, adjusting it as necessary.
Why is my DT SWISS Bicycle Accessories freewheel not engaging or slipping?
If your DT SWISS Bicycle Accessories freewheel is not engaging or slipping, there are several possible reasons: * One or both ratchets might be mounted upside down. * There might be too much or the wrong grease on the ratchets. In this case, you should clean and grease the ratchets. * The ratchets could be worn and need replacement. * One or both springs were forgotten during assembly.
What to do if my DT SWISS Bicycle Accessories wheel feels soft?
If your DT SWISS Bicycle Accessories wheel feels soft, consider the following: 1. Check the maximum permissible system weight. If it's exceeded, replace the wheels with new ones that correspond to the system weight. 2. Check the spoke tension and correct it if necessary. 3. Check the clamping in the bike and tighten it more strongly if necessary (axle or quick release).
Why is my DT SWISS Bicycle Accessories hub making noise?
If your DT SWISS Bicycle Accessories hub is making noise, it is likely that the ball bearings are worn out. Replace the ball bearings to resolve this issue.
What to do if I experience air loss with my DT SWISS Bicycle Accessories TL setup?
If you are experiencing air loss with your DT SWISS Bicycle Accessories TL setup, it's likely that the TL tape is perforated or otherwise damaged. You should apply new TL tape.
Why is my DT SWISS Bicycle Accessories hub rotating stiffly?
If your DT SWISS Bicycle Accessories hub rotates stiffly, here are a few possible causes: * The ball bearings are worn out. In this case, replace the ball bearings. * The ball bearing on the non-drive side is too tight.
What causes a blocked freewheel on DT SWISS Bicycle Accessories?
A blocked freewheel on DT SWISS Bicycle Accessories can be caused by: * A spacer being forgotten during assembly. * A spacer being compressed by overtightening the thru axle. Measure the length of the spacer; if it's shorter than 15.4 mm, it must be replaced.
What to do about decreasing braking effect with rim brakes on DT SWISS Bicycle Accessories?
If you're experiencing a decreasing braking effect with rim brakes on your DT SWISS Bicycle Accessories, it's likely due to worn or dirty brake surfaces. Clean the braking surface and pads, and replace the rim if necessary.
What causes nipples to loosen on DT SWISS Bicycle Accessories?
Nipples loosen on DT SWISS Bicycle Accessories when the maximum permissible system weight is exceeded. Re-build wheel with new PL nipples or Spoke Freeze.
What causes creaking noises from spoke crossings in DT SWISS Bicycle Accessories?
Creaking noises from spoke crossings in DT SWISS Bicycle Accessories are caused by friction of the spokes at crossing points. As a short-term solution, lightly grease/oil the crossing points.
Manual validity for product design as of 21.03.22, subject to technical changes.
Classification of safety instructions: Danger, Caution, and Note.
Manual intended for component users and dealers, offering service guidance.
Information on cover page, footing, and DT Swiss contact details.
DT Swiss manuals categorized into User and Technical Manuals.
Guidelines for general maintenance, cleaning, and tool usage.
Guidelines for waste disposal and environmental compatibility.
Liability for damage due to improper maintenance or installation.
Information on warranty conditions and where to find them.
Procedure for converting plugged-in end caps on the front wheel.
Procedure for changing pressed-on end caps on the front wheel.
Procedure for converting end caps on the rear wheel.
Recommended service intervals for small and full hub maintenance.
Crucial safety warnings for hub maintenance and spare parts.
Maintenance procedures for rear hubs with Ratchet and Ratchet LN systems.
Maintenance procedures for rear hubs with Ratchet EXP® system.
Recommended maintenance intervals for the entire wheel.
Crucial safety warnings for wheel maintenance and spare parts.
Basic procedures and tools for changing spokes and nipples.
Basics of the DT Swiss PHR system and its mounting.
Procedure for replacing a spoke with crossed lacing.
Procedure for replacing a spoke with radial lacing.
Common hub problems, their causes, and recommended solutions.
Common wheel problems, their causes, and recommended solutions.
Technical specifications for spoke tension values.
Technical specifications for wheel runout and dish tolerances.
General| Brand | DT SWISS |
|---|---|
| Model | SPLINE WHEEL |
| Category | Bicycle Accessories |
| Language | English |
To Next Page