Duraflame 9QI010ARA - User Manual

Questions and Answers

C
charles54Aug 16, 2025
Why is my Duraflame 9QI010ARA Heater blowing cold air?
- J
  Janet MaloneAug 16, 2025
  If your Duraflame Heater isn't blowing warm air, it could be due to a normal cool-down cycle, where the unit continues to run for several minutes with cool air. This duration varies based on temperature. Alternatively, it might not be reaching the set temperature. In that case, perform a master reset: turn off and unplug the unit, hold the main power button while plugging it back in, continue holding for 5 seconds after plugging it in, then release. Turn the unit back on; the temperature should flash 72 degrees then display the ambient room temperature. Also, remember this heater is designed as a supplemental heat source.
D
David HudsonAug 22, 2025
How to calibrate Duraflame 9QI010ARA Heater temperature?
- Y
  ymcgrathAug 22, 2025
  To calibrate the temperature display on your Duraflame Heater, press and hold the timer button until '00' flashes, then a single digit between -9 degrees to 9 degrees appears. Release the timer button and use the arrow up/down buttons to adjust the temperature variance up to 9 degrees +/-. The heater will exit thermostat calibration after 10 seconds without input.
R
Robert DanielsAug 26, 2025
Why does Duraflame Heater keep running after being turned off?
- J
  Justin WaltonAug 26, 2025
  It is normal for the Duraflame Heater to continue to run for several minutes after reaching the set temperature or being powered off. This is part of the cool-down cycle, during which the unit will blow cool air. Times will vary.
M
Matthew WilliamsAug 28, 2025
What does blank display mean on Duraflame Heater?
- J
  Jason AndersonAug 29, 2025
  If your Duraflame Heater display shows " ", the thermostat sensor may be broken or disconnected. Unplug the heater, remove the back panel, and check that the thermostat is plugged into the main circuit board. If this doesn't solve the problem, contact customer service for a replacement thermostat sensor.
T
Tyler CraigAug 31, 2025
Why does my Duraflame 9QI010ARA Heater turn on by itself?
- J
  jonesphillipAug 31, 2025
  If your Duraflame Heater turns on randomly, this is normal operation. The unit will periodically run to test the air temperature. It will run for 3 minutes with cool air and 3 minutes with warm air.
P
Paul WilliamsSep 3, 2025
How to fix Duraflame Heater remote when it doesn't light up?
- L
  Lynn EdwardsSep 3, 2025
  If the remote control for your Duraflame Heater is not working and the remote indicator doesn't light up when buttons are pressed, change the remote batteries.
A
Ashley GregorySep 6, 2025
What to do if Duraflame 9QI010ARA Heater buttons are not working?
- D
  David BurkeSep 6, 2025
  If the buttons on your Duraflame Heater do not work, the control panel circuit board may be defective. Replace the control panel circuit board.
T
Timothy OlsonSep 9, 2025
Why won't the Duraflame 9QI010ARA control panel light up?
- N
  nicholasshannonSep 9, 2025
  If the control panel on your Duraflame Heater does not illuminate, the control panel circuit board may be defective. Replace the control panel circuit board.
G
garciastephanieSep 10, 2025
Why does Duraflame 9QI010ARA Heater take so long to heat up?
- K
  Kelsey DonaldsonSep 12, 2025
  If your Duraflame Heater is taking a long time to heat the room, remember that it's designed as a supplemental heat source. Position the unit on an inside wall with proper insulation. Ensure the back and sides of the heater are more than 6 inches away from objects for proper air intake. Also, plug the unit directly into the wall outlet, avoiding surge protectors or extension cords. The heater provides supplemental heating for up to 800 sq/ft.
B
Brenda JonesSep 12, 2025
Why can't I change the temperature on my Duraflame Heater?
- B
  Barbara HansenSep 12, 2025
  If the temperature on your Duraflame Heater will not change, the control panel circuit board may be defective. Replace the control panel circuit board.