To Next Page
D
Dr. Justin DaySep 14, 2025
What does error ER 002 mean on my Durr Dental equipment?
- CCollin ColeSep 14, 2025
Error ER 002 indicates a door switch error condition.
What does error ER 002 mean on my Durr Dental equipment?
Error ER 002 indicates a door switch error condition.
What does error ER 110 mean on my Durr Dental equipment?
Error ER 110 indicates that the time to reach the vacuum pressure is too long.
What does error ER 140 mean on my Durr Dental equipment?
Error ER 140 means that the time to reach the sterilization pressure is too long.
What does error ER 120 mean on my Durr Dental equipment?
Error ER 120 means that the time to reach the thermodynamic discharge pressure is too long.
What does error ER 130 mean on my Durr Dental equipment?
Error ER 130 indicates that the pressure discharge time is too long.
What does error ER 360 mean on my Durr Dental equipment?
Error ER 360 means that the time to discharge the pressure has been exceeded.
What does error ER 342 mean on my Durr Dental equipment?
Error ER 342 means that the safety valve has opened during test execution.
What does error ER 355 mean on my Durr Dental equipment?
Error ER 355 means that the test execution time has been exceeded.
What does error ER 201 mean on my Durr Dental equipment?
Error ER 201 means failure to comply with the parameters in the irst phase of the vacuum test.
What does error ER 152 mean on my Durr Dental equipment?
Error ER 152 means that the theoretical temperature is over the top limit for sterilisation.
General| Brand | Durr Dental |
|---|---|
| Model | Hygoclave 40 |
| Category | Dental equipment |
| Language | English |
Overview of the autoclave's components and features, including diagrams of front and rear views.
Details the different models and configurations of the Hygoclave autoclaves available.
Highlights the key functionalities and capabilities of the steriliser, such as vacuum pump and safety devices.
Guide for the initial activation and setup of the autoclave, including language selection and warranty activation.
Explains the icons used in the autoclave interface for various functions and operations.
Outlines the main navigation structure and available menus for operating the autoclave.
Step-by-step guide on how to choose and start a sterilization cycle, including optional settings.
Details the different types of sterilization cycles available (B, S, Special) with their durations.
Provides detailed specifications for each sterilization cycle type, including temperature, pressure, and duration.
Instructions on how to properly load the autoclave chamber with materials, including load capacity.
Guides on how to fill and drain the water tanks for the autoclave using automatic or manual methods.
Information on available test cycles for validating autoclave performance, such as vacuum and Bowie & Dick tests.
Procedures for managing user accounts, PINs, and validation protocols for enhanced security.
How to configure the device's date and time settings for accurate record-keeping.
Configuration options for printer connectivity and output modes (automatic/manual print).
How to change the display language of the autoclave interface to preferred language.
Settings for pressure units (bar, kPa, mbar) and measurement types (absolute/relative).
Configuration for water filling options (front/rear) and quality monitoring.
How to establish network connections, including Ethernet setup.
Detailed guide for setting up and configuring the Ethernet network connection for remote monitoring.
Overview of maintenance operations and their recommended frequencies (daily, monthly, quarterly, annually).
Details the annual maintenance procedures performed by qualified technicians, including parts replacement.
Schedule and procedures for regular checks to ensure performance and safety, including test executions.
Lists and explains error codes, their messages, and corresponding reset procedures.
Lists and explains alarm codes, their messages, and corresponding reset procedures.
Provides solutions for various system messages displayed by the autoclave.
Explains procedures for resetting errors and returning to the initial screen.
Offers solutions for specific system messages encountered during operation.
Specifies the required water quality parameters (conductivity, chlorides, pH) for autoclave operation.
