To Next Page
C
Christy ConleySep 5, 2025
What does error ER 204 mean on my Durr Dental equipment?
- CChristian MirandaSep 5, 2025
Error ER 204 means pressure balancing failed in the vacuum test.
What does error ER 204 mean on my Durr Dental equipment?
Error ER 204 means pressure balancing failed in the vacuum test.
What does error ER 203 mean on my Durr Dental equipment?
Error ER 203 means failure to comply with the temperature limits during the vacuum test.
What does error ER 202 mean on my Durr Dental equipment?
Error ER 202 means failure to comply with the parameters in the 2nd phase of the vacuum test.
What does error ER 201 mean on my Durr Dental equipment?
Error ER 201 means failure to comply with the parameters in the irst phase of the vacuum test.
What does error ER 153 mean on my Durr Dental equipment?
Error ER 153 means that the theoretical temperature is below the bottom limit for sterilisation.
What does error ER 152 mean on my Durr Dental equipment?
Error ER 152 means that the theoretical temperature is over the top limit for sterilisation.
What does error ER 200 mean on my Durr Dental equipment?
Error ER 200 means that the time to reach the vacuum pressure is too long in the vacuum test.
What does error ER 180 mean on my Durr Dental equipment?
Error ER 180 means that the pressure balancing time is too long.
What does error ER 170 mean on my Durr Dental equipment?
Error ER 170 means that the measured pressure is below the set parameter for the drying phase.
What does error ER 160 mean on my Durr Dental equipment?
Error ER 160 indicates that the final discharge time is too long.
General| Brand | Durr Dental |
|---|---|
| Model | Hygoclave 40 |
| Category | Dental equipment |
| Language | English |
Overview of the autoclave's components and features, including diagrams of front and rear views.
Details the different models and configurations of the Hygoclave autoclaves available.
Highlights the key functionalities and capabilities of the steriliser, such as vacuum pump and safety devices.
Guide for the initial activation and setup of the autoclave, including language selection and warranty activation.
Explains the icons used in the autoclave interface for various functions and operations.
Outlines the main navigation structure and available menus for operating the autoclave.
Step-by-step guide on how to choose and start a sterilization cycle, including optional settings.
Details the different types of sterilization cycles available (B, S, Special) with their durations.
Provides detailed specifications for each sterilization cycle type, including temperature, pressure, and duration.
Instructions on how to properly load the autoclave chamber with materials, including load capacity.
Guides on how to fill and drain the water tanks for the autoclave using automatic or manual methods.
Information on available test cycles for validating autoclave performance, such as vacuum and Bowie & Dick tests.
Procedures for managing user accounts, PINs, and validation protocols for enhanced security.
How to configure the device's date and time settings for accurate record-keeping.
Configuration options for printer connectivity and output modes (automatic/manual print).
How to change the display language of the autoclave interface to preferred language.
Settings for pressure units (bar, kPa, mbar) and measurement types (absolute/relative).
Configuration for water filling options (front/rear) and quality monitoring.
How to establish network connections, including Ethernet setup.
Detailed guide for setting up and configuring the Ethernet network connection for remote monitoring.
Overview of maintenance operations and their recommended frequencies (daily, monthly, quarterly, annually).
Details the annual maintenance procedures performed by qualified technicians, including parts replacement.
Schedule and procedures for regular checks to ensure performance and safety, including test executions.
Lists and explains error codes, their messages, and corresponding reset procedures.
Lists and explains alarm codes, their messages, and corresponding reset procedures.
Provides solutions for various system messages displayed by the autoclave.
Explains procedures for resetting errors and returning to the initial screen.
Offers solutions for specific system messages encountered during operation.
Specifies the required water quality parameters (conductivity, chlorides, pH) for autoclave operation.
