Durr Dental V 600 - User Manual

Questions and Answers

M
Matthew OwensAug 3, 2025
What to do if Durr Dental equipment suction performance is too low?
- B
  briannixonAug 3, 2025
  If you're experiencing low suction performance with your Durr Dental equipment, such as at separator devices, here's what you can do: First, check and clean the coarse filters in the system, as they may be clogged. Second, inspect the suction line for any leaks and ensure the suction system and connections are leak-tight. Finally, the turbine may be mechanically sluggish due to soiling; in this case, disassemble the unit and clean the turbine.
K
kathleen36Aug 12, 2025
What to do if my Durr Dental device does not start?
- B
  Brian ReyesAug 12, 2025
  If your Durr Dental device isn't starting, begin by checking the mains supply voltage. If the voltage is too low (undervoltage), measure the supply voltage and consult an electrician if needed. Also, verify that the motor protection switch isn't set too low; measure the current and adjust the switch to the measured value plus a safety margin. Check the motor protection switch itself and replace it if it's defective. Lastly, measure the capacitance of the capacitor and replace it if necessary.
L
lhatfieldAug 23, 2025
How to fix a Durr Dental turbine blocked by solid particles?
- O
  ofrancisAug 23, 2025
  If your Durr Dental turbine is blocked, it might be due to solid particles in the turbine chamber, foam caused by incorrect cleaning agents, or condensate build-up. To resolve this, disassemble the unit and clean the turbine. If foam is present, clean both the turbine and housing. Also, inspect the pipe system to prevent over-cooling and avoid condensate build-up in the exhaust air line.

Summary

Important information

1 About this document

General information about the document's purpose and importance.

1.1 Warnings and symbols

Explains warning symbols and their meanings to indicate potential hazards.

1.2 Copyright information

Details about copyright protection for the document's content.

Safety

2.1 Intended purpose

Specifies the intended use and function of the suction unit.

2.2 Intended use

Describes how the suction unit is used in dental treatment.

2.3 Improper use

Lists uses that are considered improper and the associated risks.

2.4 General safety information

Provides general safety guidelines and regulations to follow during operation.

2.5 Combining devices safely

Advises on safe practices when connecting the unit with other systems.

2.6 Qualified personnel

Defines the qualifications required for operating and maintaining the unit.

2.7 Protection from electric shock

Outlines safety measures to prevent electric shock hazards.

2.8 Only use genuine parts

Emphasizes the importance of using only approved Dürr Dental parts.

2.9 Transport

Provides instructions and precautions for transporting the unit safely.

2.10 Disposal

Gives guidance on the proper disposal of the unit and its components.

Product description

3 Overview

Provides a visual overview of the suction unit components with labels.

3.1 Scope of delivery

Lists the items included in the standard scope of delivery for various models.

3.2 Special accessories

Details optional accessories available for purchase to enhance functionality.

3.3 Disposable materials

Lists materials that are consumed during operation and need separate ordering.

3.4 Wear parts and spare parts

Identifies parts that require regular replacement and where to find spare parts.

Technical data

4.1 V 300 S

Presents detailed technical specifications for the V 300 S model.

4.2 V 600

Provides detailed technical specifications for the V 600 model.

4.3 V 600

Presents technical specifications for the V 600 model across different configurations.

4.4 V 900 S

Details the technical specifications for the V 900 S model.

4.5 V 1200 S

Lists the technical specifications for the V 1200 S model.

4.6 Type plate

Explains the location and purpose of the unit's type plate.

4.7 Conformity assessment

States that the device meets relevant EU conformity requirements.

Requirements

6.1 Installation;setup room

Specifies requirements for the room where the unit will be installed.

6.2 Setup options

Describes different ways the unit can be set up or mounted.

6.3 Pipe materials

Lists approved and prohibited materials for vacuum pipes.

6.4 Hose materials

Details suitable and unsuitable materials for waste and suction hoses.

6.5 Information about electrical connections

Provides guidelines for safe and compliant electrical connections.

6.6 Information about connecting cables

Explains how cable diameter relates to consumption and ambient temperature.

System components

7.1 Control box

Describes the function and availability of the control box.

7.2 Bacteria filter

Recommends installing a bacteria filter for hygiene and ventilation.

7.3 Noise reduction

Suggests methods for reducing noise from exhaust air or airflow.

Installation

8.1 Installation and routeing of hoses and pipes

Guides on connecting and routing hoses and pipes for proper installation.

Electrical connections

9.1 Unit with integrated control electronics

Details the electrical connections for units with built-in control electronics.

Disinfection and cleaning

11.1 After every treatment

Outlines the cleaning procedure after each patient treatment.

11.2 Daily after the end of treatment

Describes the daily cleaning routine at the end of the workday.

11.3 Once or twice a week before the midday break

Details a more thorough cleaning procedure performed weekly.

Maintenance

12.1 V 300 S

Lists the maintenance intervals and tasks for the V 300 S model.

12.2 V 600, V 900 S, V 1200 S

Outlines maintenance intervals and tasks for V 600, V 900 S, and V 1200 S models.

Troubleshooting

Device does not start

Lists probable causes and solutions when the unit fails to start.

The unit generates unusual noises

Addresses potential causes and remedies for abnormal noises produced by the unit.

Water leaking from the exhaust air connection

Explains causes of water leakage and how to resolve them.

Suction performance too low

Identifies reasons for reduced suction performance and their solutions.

Transporting the unit

Appendix

15 Information about EMC in accordance with EN 60601-1-2

Provides information on electromagnetic compatibility standards and guidelines.

15.1 General information

General introduction to EMC information relevant to medical devices.

15.2 Abbreviations

Defines abbreviations used in the EMC section.

15.3 Guidelines and manufacturers information

Details electromagnetic emissions and guidelines for operation.

Resistance to electromagnetic interference (immunity) for all devices and systems

Outlines immunity tests and compliance levels for electromagnetic interference.

Electromagnetic interference immunity for devices or systems that are not life-sustaining

Specifies immunity requirements for non-life-sustaining devices in healthcare.

Recommended safety distance between portable and mobile HF communication devices and the unit

Provides guidelines on safe distances from HF communication devices.

Durr Dental V 600 Specifications

General

Brand	Durr Dental
Model	V 600
Category	Dental equipment
Language	English

Related product manuals

Durr Dental VistaCam iX

41 pages

Durr Dental Hygoclave 50

37 pages

Durr Dental 5252-01/Service

48 pages

Durr Dental Hygoclave 40 Plus

38 pages

Durr Dental VistaScan Mini Easy

48 pages

Durr Dental VistaScan Combi View

62 pages

Durr Dental V 600 - User Manual

Table of Contents

Questions and Answers

Summary

Important information

1 About this document

1.1 Warnings and symbols

1.2 Copyright information

Safety

2.1 Intended purpose

2.2 Intended use

2.3 Improper use

2.4 General safety information

2.5 Combining devices safely

2.6 Qualified personnel

2.7 Protection from electric shock

2.8 Only use genuine parts

2.9 Transport

2.10 Disposal

Product description

3 Overview

3.1 Scope of delivery

3.2 Special accessories

3.3 Disposable materials

3.4 Wear parts and spare parts

Technical data

4.1 V 300 S

4.2 V 600

4.3 V 600

4.4 V 900 S

4.5 V 1200 S

4.6 Type plate

4.7 Conformity assessment

Requirements

6.1 Installation;setup room

6.2 Setup options

6.3 Pipe materials

6.4 Hose materials

6.5 Information about electrical connections

6.6 Information about connecting cables

System components

7.1 Control box

7.2 Bacteria filter

7.3 Noise reduction

Installation

8.1 Installation and routeing of hoses and pipes

Electrical connections

9.1 Unit with integrated control electronics

Disinfection and cleaning

11.1 After every treatment

11.2 Daily after the end of treatment

11.3 Once or twice a week before the midday break

Maintenance

12.1 V 300 S

12.2 V 600, V 900 S, V 1200 S

Troubleshooting

Device does not start

The unit generates unusual noises

Water leaking from the exhaust air connection

Suction performance too low

Transporting the unit

Appendix

15 Information about EMC in accordance with EN 60601-1-2

15.1 General information

15.2 Abbreviations

15.3 Guidelines and manufacturers information

Resistance to electromagnetic interference (immunity) for all devices and systems

Electromagnetic interference immunity for devices or systems that are not life-sustaining

Recommended safety distance between portable and mobile HF communication devices and the unit

Durr Dental V 600 Specifications

Related product manuals