EarthQuake 9060140 User Manual (English)

Questions and Answers:

N
Nicole KirbyAug 7, 2025
What to do if the vacuum is not working on EarthQuake 9060140 Chipper?
- J
  Joshua PatrickAug 8, 2025
  If the EarthQuake Chipper's vacuum isn't working, consider these potential causes: * **Hopper lid not in place:** Install the lid. * **Material too wet:** Allow the material to dry. * **Hose not attached properly:** Attach the hose per the instructions (see the Hose Kit). * **Hose obstructed or damaged:** Clear any blockage or replace the hose. * **Engine not running at full RPM:** Set the throttle control to FAST.
P
Paul GarrettAug 13, 2025
What to do if EarthQuake Chipper runs but no material is discharged?
- C
  Crystal SosaAug 13, 2025
  If the EarthQuake Chipper engine runs, but no material is discharged, check the following: * **Discharge chute clogged:** Clean out any debris. * **Engine not running at full speed:** Set the throttle control to FAST.
T
Thomas OlsonAug 20, 2025
Why EarthQuake 9060140 engine exhaust is black?
- J
  Jack MendozaAug 20, 2025
  Black exhaust from your EarthQuake Chipper engine can result from: * **Dirty air filter:** Replace the air filter (refer to the engine manual). * **Choke closed:** Open the choke.
C
Caitlin ValdezAug 26, 2025
Why is there unusual noise or vibration when chipping materials with EarthQuake 9060140?
- M
  Michelle FranklinAug 27, 2025
  Unusual noise or vibration when chipping materials with your EarthQuake Chipper can be caused by: * **Rotor overloaded with material:** Allow the unit to clear itself before adding more material to the hopper. * **Hammers are broken, bent, or loose:** Check the assembly and tighten or replace parts as necessary. * **Hammers frozen in place:** Check for obstructions and debris, then repair or replace parts as needed.
A
antoniobradshawAug 31, 2025
Why is there excessive branch vibration when chipping materials with EarthQuake Chipper?
- R
  reillydarleneAug 31, 2025
  Excessive branch vibration when chipping materials with your EarthQuake Chipper may occur due to: * **Chipper knives dull:** Sharpen or replace the chipper knives. * **Tree limbs are extremely hard or dried out:** The material may not be suitable for chipping.

EarthQuake 9060140 Specifications

General

Brand	EarthQuake
Model	9060140
Category	Chipper
Language	English

Summary

Introduction and Emissions Information

Federal Emissions Information

Information regarding engine emissions compliance with EPA regulations.

Registration and Service

Instructions for registering the product warranty and obtaining service.

Safety Guidelines

Owner's Responsibility

Outlines the owner's duties for safe and effective use of the equipment.

Important Safety Precautions

Detailed safety precautions to be read and followed before operation.

California Proposition 65 Warning

Warning about chemicals in engine exhaust known to cause cancer or reproductive harm.

Preparation Guidelines

Guidelines on appropriate attire and initial checks before operating the equipment.

General Operation and Safety

Training Requirements

Emphasizes the importance of reading instructions and understanding controls for safe operation.

General Operating Procedures

Provides essential guidelines and precautions for general operation of the chipper/shredder.

Child Safety

Critical safety advice regarding the presence and interaction of children.

Service and Maintenance

General guidelines for maintaining and servicing the chipper/shredder.

Safety Decals and Icons

North American Safety Decals

Details of safety decals for operating instructions on North American models.

European Safety Icons

Explanation of safety icons used on European models of the chipper/shredder.

Amputation Hazard Warning

Warning about amputation hazard from rotating blades, advising to keep hands out of inlet.

Spark Plug Wire Disconnection Warning

Crucial safety warning to disconnect the spark plug before performing any maintenance.

Identification Numbers

CE Identification Tag Markings

Details about markings on the CE identification tag related to compliance standards.

Assembly Instructions

Install Chipper Cone

Instructions for attaching the chipper cone assembly to the engine.

Install the Hopper

Instructions for attaching the hopper to the rotor housing.

Attach Hopper Extension

Step-by-step guide for attaching the hopper extension to European models.

Features and Controls

Control Functions Overview

Brief explanation of the function of individual controls on the unit.

Operating Procedures

Chipper Operation

Specific instructions and tips for operating the chipper function safely.

Shredder Operation

Specific instructions and tips for operating the shredder function safely.

Adding Fuel

Step-by-step instructions for safely adding fuel to the engine.

Starting the Engine

Detailed procedure for starting the chipper/shredder engine.

Stopping and Processing

Stopping the Engine

Procedures for safely stopping the engine and the unit.

Processing Materials

Tips and recommendations for efficiently processing various materials.

Storage Instructions

Instructions and precautions for storing the unit, especially for the off-season.

Chipping & Shredding Recommendations

Maintenance Schedule

Schedule and Procedures Overview

A table outlining the maintenance schedule and specific procedures by time intervals.

Clean Debris from Engine & Chipper

Procedures for cleaning debris from the engine cooling fins and chipper components.

Inspect and Rotate Shredding Hammers

Instructions for inspecting and rotating shredding hammers for optimal performance.

Inspect Chipping Knives

Procedures for inspecting and maintaining the chipping knives.

Check and Change Engine Air Cleaner

Instructions for checking and replacing the engine air filter and pre-cleaner.

Replace Spark Plug

Recommendation to contact an authorized dealer for spark plug replacement.

Engine Oil Management

Check Engine Oil Level

Procedure for checking the engine oil level before each use.

Change Engine Oil

Step-by-step instructions for changing the engine oil.

Troubleshooting Guide

Repair Procedures

Shredding Hammer Rotation and Replacement

Procedures for rotating or replacing shredding hammers.

Chipping Knives Sharpening and Replacement

Instructions for sharpening or replacing the chipping knives.

Specifications and Parts

Chassis Specifications

Specifications related to the chassis, including capacity and weight.

Replacement Parts

Details on obtaining genuine replacement parts from an authorized dealer.

Optional Accessories

Information on available optional accessories like vacuum and tow bar kits.

Parts Diagrams

Hopper & Engine Group Parts Explosion

Exploded view diagram of the hopper and engine components.

Hopper & Engine Group Parts List

Detailed parts list for the hopper and engine group.

Housing & Rotor Group Parts Explosion

Exploded view diagram of the housing and rotor components.

Housing & Rotor Group Parts List

Detailed parts list for the housing and rotor group.

Vacuum Kit Parts

Diagram and parts list for the optional vacuum kit accessory.

Tow Bar Kit Parts

Diagram and parts list for the optional tow bar kit accessory.

Hopper Extension Parts Diagram

Diagram and parts list for hopper extension assembly on CE European models.

Declarations of Conformity

Declaration of Conformity (General)

Official declaration of the product's compliance with relevant EC directives.

EC Declaration of Conformity (Noise)

Declaration of conformity specifically concerning the outdoor noise directive.

Declaration of Conformity (Model Specific)

Declaration of conformity for a specific model, referencing EC directives.

EC Declaration of Conformity (Noise - Model Specific)

Declaration of conformity regarding outdoor noise levels for a specific model.

Warranty Information

Product Warranty Terms

Comprehensive terms and conditions for the product's limited warranty.

Engine Emissions Control Warranty

Specific warranty details for the Viper engines regarding emissions control.

Emissions Control Warranty Provisions

Detailed explanation of the emissions control warranty provisions and coverage.

Maintenance and Repair Requirements

Owner's responsibilities for maintenance and repair to maintain warranty validity.

Notes

Related product manuals

EarthQuake 9060300

40 pages

EarthQuake 14267