Why is my Eaton 9E6Ki UPS on battery when mains voltage is present?
If your Eaton UPS is running on battery even when mains voltage is present, it means the input voltage is outside the permitted tolerance range for mains operation. This indicates a problem with the mains supply. Wait for the input mains voltage to return within the acceptable range; the UPS will automatically switch back to mains operation.
What to do if Eaton 9E6Ki beeps and shows F704, F70D,F70C,F302, F303,F305,F300,F301,F304, or F002?
If your Eaton UPS buzzer sounds continuously and the display shows code F704, F70D, F70C, F302, F303, F305, F300, F301, F304, or F002, the UPS is malfunctioning. If possible, disconnect the power to the load, switch the UPS off and back on again. If the problem persists, contact the support center.
How to fix Eaton UPS display not lighting up?
If the display of your Eaton UPS doesn't light up, check the following: * Ensure the input switch on the back of the UPS is closed. * Verify the power cable is correctly connected. * Confirm that power is reaching the UPS (no blackout). * Reset the thermal protection, but first, ensure there's no output overload to the UPS.
What to do if Eaton 9E6Ki beeps and shows A80E, A810, or F808?
If your Eaton UPS buzzer sounds continuously and the display shows code A80E, A810, or F808, the load applied to the UPS is too high. Reduce the load to within 100% of the threshold (or the user threshold in the case of code A80E). If the display shows a fault, remove the load and switch the UPS off and back on again.
What does it mean when Eaton 9E6Ki beeps and shows code F805?
If the buzzer of your Eaton UPS is sounding continuously and the display shows code F805, there is a fault on one or more of the loads powered by the UPS. To resolve this, disconnect all the utilities, switch the UPS off and back on again. Then, reconnect the utilities one at a time to identify the faulty one.
What to do if Eaton UPS buzzer sounds with codes A80E, A810, or F808?
If your Eaton UPS buzzer sounds continuously and the display shows codes A80E, A810, or F808, it indicates that the load applied to the UPS is too high. Reduce the load to within the threshold of 100% (or the user threshold in the case of code A80E). If the display shows a fault, remove the load and switch the UPS off and back on again.
What does it mean if my Eaton 9E6Ki display shows the code A900?
If the display of your Eaton UPS shows the code A900, it means the maintenance bypass function is active. To take the UPS out of the maintenance bypass function, open the manual bypass switch on the back of the UPS.
How to fix Eaton 9E6Ki UPS when the display does not light up?
If the display of your Eaton UPS doesn't light up, it could be due to several reasons. First, ensure that the input switch located on the back of the UPS is closed. Also, verify that the main connection cable is correctly connected. Check that the power reaches the UPS and reset the thermal protection, making sure there is no output overload.
What to do if Eaton 9E6Ki display is on but no power to load?
If the display is on but the load is not powered by your Eaton UPS, the UPS might be in standby mode. Press the 'ON' button on the front panel to power the loads.
What to do if my Eaton 9E6Ki UPS buzzer sounds continuously and shows codes F704, F70D, F70C, F302, F303, F305, F300, F301, F304, or F002?
If your Eaton UPS buzzer sounds continuously and the display shows codes F704, F70D,F70C,F302, F303,F305,F300,F301,F3 04, or F002, it suggests the UPS is malfunctioning. If possible, disconnect the power to the load, switch the UPS off and back on again.
General| Input Frequency | 50/60 Hz |
|---|---|
| Output Frequency | 50/60 Hz |
| Output power factor | 0.9 |
| Efficiency | 95% |
| Form Factor | Tower |
| Extended Battery Capability | Yes |
| Power Rating | 6000 VA |
| Input Voltage | 220-240 V |
| Output Voltage | 220-240 V |
| Battery Type | Lead-acid |
| Topology | Online Double Conversion |
| Communication | USB, Serial |
Provides essential safety guidelines for installation, operation, and maintenance of the UPS.
Specifies prerequisites and safety requirements before connecting the UPS.
Instructions for connecting the UPS power and load cables correctly.
Instructions for connecting external battery modules (EBM) to the UPS.
Provides a guide to identify and resolve common UPS problems and error codes.
Lists and explains various alarm codes indicating minor UPS problems.
To Next Page
