Eaton Cutler-Hammer FP-6000 Series - Page 18

Instructional Literature
Page 18 Effective: May 2008
Instructions for the FP-6000 Protective Relay
For more information visit: www.eaton.com IB02602004E
3 Specifications
3.1 Table of Specifications
Note that accuracy specifications for the FP-6000 are for operation within the nominal frequency range of 50 Hz or 60 Hz at + 5 Hz.
Unless stated otherwise, Operating Power Factors “0.50 Lagging” to “Unity” to “0.50 Leading
”.
Table 5. Table of Specifications
CONTROL POWER: TB101-102 (101 POSITIVE FOR DC)
Standard Power Supply Board 250V Power Supply Board
ac Nominal Voltage 100 – 120 Vac 100 – 240 Vac
ac Excursion Range 55 – 132 Vac 55 – 264 Vac
ac Frequency Range 50/60 Hz nom. +
5% 50/60 Hz nom. + 5%
dc Nominal Voltage 48 – 125 Vdc 100 – 250 Vdc
dc Excursion Range 38 – 150 Vdc 80 – 300 Vdc
Interruption Ride Through Time 83ms for 120V, 60 Hz ac 250ms for 110 Vdc
300ms for 110 Vdc
Power Consumption 20 VA Max. 20 VA 22 VA
CURRENT TRANSFORMER INPUTS: TB4 A, B, C, X
FP-6200-00 FP-6300-00
Nominal (I
nom
): 5 A 1 A
CT Rating: Steady State
Maximum Transient
2 x I
nom
= 10 A
80 x I
nom
= 400 A for 1 sec.
3 x I
nom
= 3 A
100 x I
nom
= 100 A for 1 sec.
CT Burdens < 0.25 VA @ 5 A (Nominal) < 0.05 VA @ 1 A (Nominal)
CONTACT INPUTS: TB201-204, 206-209, SOURCE TB205, 210
Number of Contact Inputs Cin1 – Cin8
Rating 40 Vdc @ 2 mA/C In draw wetting voltage provided with internal return only
VOLTAGE TRANSFORMER INPUTS: TB213-217, VA, VB, VC, VX1, VX2
Nominal 0 – 120 Vac Line to common
Operating Range 0 – 144 Vac (+20%) Line to common
Internal Burden Loading 1 Meg Input Impedance
Reference TB218, Vg internal 120 ohm PTC to chassis ground
RELAY OUTPUT: TB103-118
Number & type of output contacts 2 Form C, NO & NC TB103-105, 106-108
5 Form A, NO only
TB109/110, 111/112, 113/114, 115/116, 117/118
RELAY OUTPUT CONTACTS RATING: BOTH FORM A & C
Standard Power Supply Board 250V Power Supply Board
Momentary Make 30 A ac/dc for 0.25 seconds up to 120 Vac or 125 Vdc Make 30 A ac/dc for 0.25 seconds up to 240 Vac or 250 Vdc
Break 0.5 A @ 125 Vdc (resistive) Break 0.5 A @ 125 Vdc (resistive)
Break 5 A @ 30 Vdc Break .25 A @ 250 Vac (resistive)
Break 5 A @ 120 Vac Break 5A @ 30 Vdc
Break 5A @ 240 Vac
Continuous 5 A @ 120 Vac 5 A @ 240 Vac
5 A @ 125 Vdc 5 A @ 250 Vdc