Eaton MPS12-30 - User Manual

To Next Page

How to replace the battery

Contact your MPS12-30 supplier to purchase a replacement battery.

Warning: Risk of explosion if incorrect battery type is used.

Battery can be replaced with MPS12-30 connected to AC wall

socket/outlet.

1. Press the battery cover and

slide up.

2. Remove the cover.

3. Take out the battery.

4. Disconnect the battery

wires.

5. Connect the wires to new

battery. Red: positive (+),

Black: negative (-).

Warning: Reverse connection

may damage the MPS12-30.

6. Place the new battery in the

MPS12-30.

7. Replace the battery cover.

Recycle old batteries according to local regulations. Or contact

your MPS12-30 supplier for advice.

Specifications

AC Supply 80-260V ac, 45-65Hz

Output Voltage 12V dc nominal, 10.5 - 13.8V dc

Output Power 30W maximum

Battery Type VRLA, Hot Swappable

12V, 7Ah (12V, 9Ah can be fitted)

Backup time (@ 1A

discharge)

5 hours typical

Recharge Time 4 hours to 90%, without load after

complete discharge

Discharge Prevention 10.5V ± 0.5V

Rated Charging Voltage 13.7V ± 0.25V

Charge Current 2.5A maximum

Output Terminals Screw connect, maximum wire

size

0.5 - 2.0mm

/ 20 - 14 AWG

Alarms Open collector

DC output cable size 1.5mm

/ 14 AWG recommended

DC output cable length 6m / 20 feet maximum

Operating Temperature 0°C to 40°C / 32°F to 104°F

Operating Humidity 0% to 90%

Operating Elevation 0 to 3000m / 0 to 9800 feet

Dimensions 120mm W, 368mm H, 81mm D

4.7" W, 14.5" H, 3.2" D

Weight 3.5kg / 7.7 lb

Eaton Corporation disclaims any liability for direct, indirect, incidental, special or

consequential damages arising out of the application or use of any information

contained in this document. The foregoing disclaimer applies to damages or

personal injury, property damage, loss of operation, loss of profits, loss of product

or loss of time, whether incurred by the purchaser, the purchaser’s employees or

third party.

Information in this document does not constitute a warranty, representation or

guarantee concerning the suitability or performance of Eaton products. No such

warranty, representation or guarantee is expressed or implied.

Information contained in this document is subject to change without further notice.

Subject to the right to use its equipment, Eaton Corporation does not convey any

right, title or interest in its intellectual property, including, without limitation, its

patents, copyrights and know-how.

No part of this document may be reproduced or transmitted in any form, by any

means or for any purpose other than the Purchaser’s personal use, without the

express written permission of Eaton Corporation.

Eaton® is a trade name, trademark, and/or service mark of Eaton Corporation or

its subsidiaries and affiliates. Unless otherwise noted, brands, product names,

trademarks or registered trademarks are the property of their respective holders.

IPN: 997-00012-75A September 2009

MPS12-30

Micro Power Solutions

Installation and Operation

Guide

Main Page

Need help?

Do you have a question about the Eaton MPS12-30 and is the answer not in the manual?

Summary

Front and Rear View

Component Identification

Details the physical layout and identifies key components and connectors on the MPS12-30.

Safety and Preparation

Important Safety Warnings

Crucial safety precautions and potential risks associated with the device's operation.

Package Contents

Lists the items included in the MPS12-30 package.

Installation Requirements

Lists necessary tools and cables for installing the MPS12-30.

Installation Procedures

How to Connect the MPS12-30

Step-by-step instructions for connecting the MPS12-30 to power and equipment.

How to Mount the MPS12-30

Guidance on selecting a suitable location and mounting the MPS12-30.

Operation and Monitoring

How to Turn On

Steps to power on the MPS12-30 and initial checks.

Understanding Lights and Alarms

Explains the meaning of different indicator lights and alarm sounds.

Battery Maintenance

How to Replace the Battery

Detailed steps for safely replacing the internal battery of the MPS12-30.

Product Specifications