ebm-papst R3G250-PR17-I1 - User Manual

Operating instructions
R3G250-PR17-I1
Translation of the original operating instructions
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 7938 81-0
Fax +49 (0) 7938 81-110
info1@de.ebmpapst.com
www.ebmpapst.com
CONTENTS
1. SAFETY REGULATIONS AND INFORMATION
11. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1.1 Hazard levels for warnings
11.1 Hazard levels for warnings
These operating instructions use the following hazard levels to indicate
potentially hazardous situations and important safety regulations:
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
1.2 Staff qualifications
11.2 Staff qualifications
The device may only be transported, unpacked, installed, operated,
maintained and otherwise used by suitably qualified, trained and
authorized technical staff.
Only authorized specialists are permitted to install the device, to carry
out a test run and to perform work on the electrical installation.
1.3 Basic safety rules
11.3 Basic safety rules
The safety hazards associated with the device must be assessed again
following installation in the final product.
The locally applicable industrial safety regulations are always to be
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
11.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 6.3 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
21.5 Safety and protective features
21.6 Electromagnetic radiation
21.7 Mechanical movement
21.8 Emissions
21.9 Hot surface
21.10 Transport
21.11 Storage
32. INTENDED USE
43. TECHNICAL DATA
43.1 Product drawing
63.2 Nominal data
63.3 Data according to Commission Regulation (EU) 327/2011
63.4 Technical description
73.5 Mounting data
73.6 Transport and storage conditions
73.7 Electromagnetic compatibility
74. CONNECTION AND STARTUP
74.1 Mechanical connection
74.2 Electrical connection
84.3 Connecting the cables
84.4 Factory settings
94.5 Connection diagram
104.6 Checking connections
104.7 Switching on the device
104.8 Switching off the device
105. INTEGRATED PROTECTIVE FEATURES
106. MAINTENANCE, MALFUNCTIONS, POSSIBLE
CAUSES AND REMEDIES
116.1 Vibration testing
116.2 Cleaning
116.3 Safety inspection
126.4 Disposal
Item no. 54443-5-9970 · ENU · Change 229573 · Approved 2021-06-09 · Page 1 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary

SAFETY REGULATIONS AND INFORMATION

Hazard Levels for Warnings

Explains hazard symbols and their meanings (DANGER, WARNING, CAUTION, NOTE).

Staff Qualifications

Specifies required qualifications for operating personnel to ensure safe use.

Basic Safety Rules

Outlines fundamental safety rules for handling and working with the device.

Electrical Voltage Safety

Warns about electrical hazards and mandates specific safety practices.

Safety and Protective Features

Details essential safety features and their importance for preventing injury.

Electromagnetic Radiation

Addresses potential electromagnetic interference and shielding requirements.

Mechanical Movement Safety

Emphasizes safety precautions when interacting with moving parts.

Emissions and Noise Levels

Informs about potential emissions and noise levels, requiring hearing protection.

Hot Surface Hazards

Warns about hot surfaces and the risk of burns, requiring protection.

Transport and Storage Instructions

Provides guidance on proper transportation and storage conditions.

INTENDED USE

Permitted Applications and Conditions

Lists approved uses, operating conditions, and system requirements.

Prohibited and Improper Uses

Details specific operations that are forbidden and potentially hazardous.

TECHNICAL DATA

Product Drawing and Dimensions

Presents a detailed technical drawing with all relevant dimensions.

Nominal Data and Specifications

Lists key technical specifications like voltage, current, speed, and power.

EU Energy Efficiency Data

Details energy efficiency metrics as required by EU Commission Regulation.

Technical Description and Features

Describes technical aspects, materials, protection class, and operational features.

Mounting Data and Conditions

Specifies screw strength class and clearance for mounting.

Electromagnetic Compatibility Standards

Lists standards for EMC immunity and interference emission.

CONNECTION AND STARTUP

Mechanical Connection Procedures

Provides instructions and warnings for physically connecting the device.

Electrical Connection Safety

Details safety precautions and requirements for electrical hookup.

Wiring Requirements and Diagrams

Covers cable requirements, reactive currents, RCCB, and connection diagrams.

Factory Settings and Parameters

Lists default settings for mode parameters and other device functions.

Connection Checking and Startup

Procedures and safety checks before powering up the device.

Device Switching Procedures

Instructions for safely switching the device off during operation and maintenance.

INTEGRATED PROTECTIVE FEATURES

Faults and Automatic Motor Shutdown

Lists faults that trigger automatic motor shutdown and restart behavior.

MAINTENANCE, MALFUNCTIONS, AND REMEDIES

Troubleshooting Common Malfunctions

Identifies common malfunctions, their causes, and suggested remedies.

Resolving Electrical and Voltage Issues

Troubleshooting steps for line voltage, faulty connections, and overtemperature.

Vibration Testing and Analysis

Guidelines and frequency for checking mechanical vibration.

Cleaning Instructions and Precautions

Instructions for cleaning the device to ensure longevity and prevent damage.

Safety Inspection Procedures

Periodic checks for contact protection and visual inspection guidelines.

Component Inspection and Damage Checks

Visual inspection procedures for blades, housing, cables, impeller, and holes.

Disposal and Environmental Considerations

General guidance and recommendations for product disposal and environmental protection.

Disassembly Safety and Component Recycling

Safety warnings for disassembly and guidance on component recycling.

ebm-papst R3G250-PR17-I1 Specifications