EasyManua.ls Logo

Echo CS-310ES - User Manual

Echo CS-310ES
9 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
CS-310ES
01-30B-00
1
INTRODUCTION
We are constantly working on technical im-
provement of our products. For this reason,
technical data, equipment and design are
subject to change without notice. All speci-
fications, illustrations and directions in this
SERVICE DATA are based on the latest
product information available at the time of
publication.
0
SERVICE DATA
CHAIN SAW
CS-310ES
STAGE MODEL
(Serial number : 37000001 and after)
CONTENTS
page
1 SERVICE INFORMATION
.............................. 2
1-1 Specifi cation ............................................... 2
1-2 Technical data ............................................. 3
1-3 Torque limits................................................ 4
1-4 Special repairing materials ......................... 4
1-5 Service limits............................................... 5
1-6 Special tools ............................................... 6
2 CARBURETTOR ADJUSTMENT PROCEDURE
.. 7
2-1 General adjusting rules ............................... 7
2-2 Presetting Idle adjust screw, L mixture needle
and H mixture needle ........................................ 7
2-3 Adjusting carburettor................................... 9
Reference No.
01-30B-00
ISSUED: 200812

Table of Contents

Questions and Answers

  • T
    tylermeyersJul 29, 2025
    What to do if my Echo Chainsaw has no spark at the plug?
    • K
      Kristen Torres MDJul 29, 2025
      If there's no spark at the plug of your Echo Chainsaw, it might be due to an incorrect spark gap. Adjust it to 0.6 to 0.7 mm. Alternatively, the spark plug might be covered with carbon or fouled with fuel, in which case you should clean or replace it. The spark plug itself could also be defective, requiring replacement.
  • T
    Timothy TranAug 4, 2025
    Why is my Echo CS-310ES Chainsaw silencer wet with fuel?
    • A
      andrewsdanielAug 4, 2025
      If the silencer of your Echo Chainsaw is wet with fuel, it's likely that the fuel mixture is too rich. Try opening the choke, cleaning or replacing the air filter, or adjusting the carburetor. For further assistance, consult your ECHO dealer.
  • J
    Julie ReedAug 10, 2025
    What to do if my Echo CS-310ES has no fuel at carburettor?
    • A
      April GonzalezAug 10, 2025
      If your Echo Chainsaw has no fuel at the carburettor, the fuel filter or fuel line might be clogged. Try cleaning or replacing the fuel filter and cleaning the fuel line. For carburettor issues, consult your ECHO dealer.
  • M
    Michelle JohnsonAug 16, 2025
    Why does my Echo CS-310ES engine run but dies or accelerates poorly?
    • C
      Christopher HodgesAug 16, 2025
      Your Echo Chainsaw might be experiencing issues like a dirty air filter, fuel filter, or a plugged fuel vent. Other potential causes include a fouled spark plug, carburetor issues, a plugged cooling system, or a blocked exhaust port/silencer. You can try to clean or replace the air filter, fuel filter, clean the fuel vent, clean and adjust or replace the spark plug, adjust the carburettor, clean the cooling system, or clean the exhaust port/silencer.
  • D
    daviskristyAug 22, 2025
    What to do if my Echo CS-310ES has no spark at end of plug wire?
    • C
      Catherine PerkinsAug 22, 2025
      If there is no spark at the end of the plug wire of your Echo Chainsaw, first ensure the ignition switch is turned on. If the problem persists, it may be an electrical issue, and you should consult your ECHO dealer.

Echo CS-310ES Specifications

General IconGeneral
Engine Displacement30.5 cc
Engine Type2-stroke
Bar Length14 inches
Fuel Capacity8.5 oz
Weight4.0 kg (8.8 lbs) without bar and chain
Power Output1.1 kW
Chain Pitch3/8 inch
Chain Gauge0.050 inches

Related product manuals