To Next PageTo Next Page
Need help?Do you have a question about the Echo PAS-260 PRO - PARTS CATALOG SERIAL NUMBER 05001001-05999999 and is the answer not in the manual?
Main engine housing for protection and component mounting.
Protective cover for the top of the engine assembly.
Housing for the muffler component.
Component for supporting the fuel tank assembly.
Reservoir for storing fuel for the engine.
Assembly that allows air into the fuel tank.
Tubing for venting the fuel tank.
Tubing for returning fuel.
Tubing for supplying fuel to the engine.
Sealing component for fuel lines.
Component that filters fuel before it reaches the engine.
Assembly for sealing the fuel tank cap.
Seal for the fuel tank cap.
Connector for the fuel tank cap.
Retaining ring used in various assemblies.
Component for securing the main pipe.
Assembly for the fan cover, protecting internal components.
Housing for the fan assembly.
Component that reduces friction for rotating parts.
Part of the clutch that engages with the shoes.
Movable part of the clutch that engages the drum.
Shaft connecting the clutch components.
Spring that controls clutch engagement/disengagement.
Pawl assembly for the starter mechanism.
Retaining ring for securing components.
Spring for returning starter components.
Pawl that engages with the starter mechanism.
Complete assembly for starting the engine.
Drum component of the starter assembly.
Pull rope for starting the engine.
Component that guides the starter rope.
Handle for pulling the starter rope.
Spring for rewinding the starter rope.
Knob used for fastening components.
Cover for the air cleaner assembly.
Component that filters air entering the engine.
Plate for preventing something, likely debris.
Housing for the air cleaner.
Seal for intake components.
Component providing thermal or electrical insulation.
The fuel metering device for the engine.
Bracket for mounting engine cables.
Assembly controlling engine throttle.
Screw for adjusting engine idle speed.
Rotating connector component.
Main housing of the carburetor.
Sealing ring for various components.
Small orifice controlling fuel flow in the carburetor.
Housing for the fuel pump assembly.
Filter screen for the carburetor inlet.
Spring for the metering lever.
Needle valve controlling fuel into the float bowl.
Lever that operates the metering valve.
Pin securing the metering lever.
Body for the air purge system.
Purge bulb for priming the carburetor.
Cover for the primer pump.
Kit containing essential parts for carburetor repair.
Sealing ring.
Gasket for the fuel pump.
Diaphragm for the fuel pump.
Gasket for the metering diaphragm.
Diaphragm for fuel metering.
Kit containing gaskets and diaphragms.
The fuel metering device for the engine.
Cap for limiting adjustment range.
Bracket for mounting engine cables.
Assembly controlling engine throttle.
Screw for adjusting engine idle speed.
Rotating connector component.
Main housing of the carburetor.
Needle for high-speed fuel adjustment.
Housing for the fuel pump assembly.
Filter screen for the carburetor inlet.
Spring for the metering lever.
Needle valve controlling fuel into the float bowl.
Lever that operates the metering valve.
Pin securing the metering lever.
Body for the air purge system.
Purge bulb for priming the carburetor.
Cover for the primer pump.
Kit containing essential parts for carburetor repair.
Sealing ring.
Gasket for the fuel pump.
Diaphragm for the fuel pump.
Gasket for the metering diaphragm.
Diaphragm for fuel metering.
Kit containing gaskets and diaphragms.
Protective shield for the exhaust components.
Component that reduces engine noise.
Screen for the muffler assembly.
Seal for exhaust connections.
Component that directs exhaust gases.
Component that generates high voltage for the spark plug.
Insulating tube for electrical connections.
Sealing or vibration dampening component.
Cap that connects the ignition wire to the spark plug.
Terminal for the spark plug cap connection.
Component that ignites the fuel-air mixture.
Wire connecting the ignition coil to the spark plug.
Rotating component that stores rotational energy.
Wire for grounding electrical components.
The primary engine block containing core components.
The chamber where combustion occurs.
Seal between the cylinder and engine block.
Kit containing piston, rings, and pin.
Seals between the piston and cylinder wall.
Pin connecting the piston to the connecting rod.
Retaining clip for the piston pin.
Spacer for the piston pin assembly.
Needle bearing for rotating parts.
Component converting linear piston motion to rotation.
Kit for the crankcase assembly.
Seal preventing oil leakage.
Ball bearing for smooth rotation.
Retaining clip for specific shaft diameter.
Seal for the crankcase.
Protective shield for exhaust components.
Main conduit for power transmission.
Component that stops movement.
Flexible internal lining.
Flexible shaft transmitting power.
Warning or informational label.
Ring assembly for securing a harness.
Component for connecting drive shafts.
Latching mechanism assembly.
Handle for operation or adjustment.
Flat ring used with fasteners.
Fastener with a threaded shaft.
Fastener that threads onto a bolt.
Fastener with a threaded shaft and head.
Device for hanging attachments.
Assembly for the front user grip and control.
The part of the handle the user grips.
The main structural part of the front handle.
Upper bracket for the handle assembly.
Lower bracket for the handle assembly.
Safety bar to prevent contact with moving parts.
Kit for the main operator control handle.
Band assembly for securing components.
Lever operated by the user to control engine speed.
Cable connecting the throttle trigger to the carburetor.
Protective corrugated cover.
Spring for returning the throttle trigger.
Mechanism to prevent unintended throttle operation.
Lever for the throttle lockout.
Spring for the throttle lockout mechanism.
Assembly for controlling engine ignition.
Knob for operating the ignition switch.
Label indicating switch function.
The part of the handle the user grips.
Kit for clamping components.
Label indicating choke operation.
Manufacturer's brand label.
Label with spark plug information.
Label identifying the product model.
Warning label for hot surfaces.
Seal for the crankcase.
Seal for intake components.
Seal for exhaust connections.
Seal between the cylinder and engine block.
Protective shield for exhaust components.
Combination wrench and screwdriver tool.
Tool for tightening/loosening nuts and bolts.
Bar used to lock components in place.
Wrench with open ends for fasteners.
Bar with hexagonal cross-section for specific uses.
L-shaped tool for hexagonal sockets.
Tool for Torx fasteners.
Tool for driving screws.
Key for operating a chuck.
General