ECOSTAR ECO 400 User Manual (English)

Other manuals for ECOSTAR ECO 400

Operating And Maintenance Manual78 pages

Questions and Answers:

G
gsnowAug 19, 2025
What to do if ECOSTAR ECO 400 cannot be commissioned?
- T
  Timothy HaysAug 20, 2025
  If your ECOSTAR Burner cannot be commissioned, there are several potential causes and solutions: * **Fuel Issue:** The fuel valve might be closed, preventing fuel from reaching the burner. Open the valve to resolve this. * **Fuse Problem:** Check the burner power supply for a tripped fuse, either on the main panel or the burner itself. * **Relay Problem:** Reset the thermal relay and check its adjustment according to the current indicated on the motor label. If the problem persists, the thermal relay may need replacement. * **Thermostat/Switch Issue:** A faulty boiler thermostat, pressure switch, or steam tank issue related to an unadjusted or broken water level device may be the cause. Adjust the water level device, and replace it if necessary.
J
Jason FrancisAug 22, 2025
What to do if ECOSTAR ECO 400 starts up, but fails after 30 seconds?
- A
  Ashley Webb MDAug 22, 2025
  If your ECOSTAR Burner starts up but fails after 30 seconds, consider these potential issues: * **Fuel Valve/Pressure:** The fuel valve may be closed, or the fuel supply pressure might be too low. Check the fuel inlet manometer. * **Ignition Electrodes:** The ignition electrodes may be misadjusted, or the ignition cables might have detached from their terminals. Adjust the ignition electrodes to maintain a distance of 3-5 mm between them.
G
Gabriel PerezAug 25, 2025
Why does ECOSTAR Burner flame appear and go into failure mode?
- M
  michele05Aug 25, 2025
  If the ECOSTAR Burner flame appears and then goes into failure mode, it could be due to: * **Fuel Pressure Error:** The fuel pressure in the circuit might have dropped. * **Photocell Failure:** The photocell may be faulty or contaminated. Try removing and cleaning it. * **Program Relay Failure:** The program relay may have failed and needs replacing with a new one.
M
melissa23Aug 26, 2025
What to do if ECOSTAR ECO 400 starts up, but fails after 10 seconds?
- W
  William HenryAug 26, 2025
  If your ECOSTAR Burner starts up but fails after 10 seconds, the following could be the reason: * **Program Relay Failure:** Replace the program relay with a new one. * **Fan Motor Failure:** Check the fan motor coils, motor contactor, and the outlet from the program relay.
D
Daniel AcevedoAug 27, 2025
How to fix ECOSTAR ECO 400 Burner boiler cover overheating?
- S
  Shelly AndrewsAug 27, 2025
  If the boiler cover is overheating, ensure proper sealing between the boiler cover and the burner. If necessary, use insulating material between the boiler connecting flange and the boiler cover.
J
Jo StevensAug 29, 2025
What to do if ECOSTAR Indoor Fireplace burner starts up, but fails after 30 seconds?
- M
  Michael AndersonAug 29, 2025
  If the ECOSTAR Indoor Fireplace burner starts but fails after 30 seconds, it could be due to a drop in heavy oil or gas pressure. Inspect the heavy oil or gas inlet manometer. Another cause could be the ignition electrode failure. In that case, adjust the ignition electrodes to maintain a distance of 3-5 mm between them.
J
Jordan WoodsAug 31, 2025
Why does my ECOSTAR Indoor Fireplace burner start up, but fail after 10 seconds?
- A
  Amy FoxAug 31, 2025
  If the ECOSTAR Indoor Fireplace burner starts up but fails after 10 seconds, it could be due to a program relay failure; replace it with a new one. Another potential cause is a fan motor failure. Check the fan motor coils, motor contactor, and outlet from the program relay.
T
Tami RamosSep 2, 2025
How to troubleshoot ECOSTAR Indoor Fireplace burner that cannot be commissioned?
- C
  craig86Sep 3, 2025
  If the ECOSTAR Indoor Fireplace burner cannot be commissioned, it might be due to several reasons. * First, check if the heavy oil or gas is cut or does not come; if so, open the valve. * Second, a fuse failure may occur; check the burner power supply, as the fuse on the main panel or the burner might be tripped. * Third, a relay failure may occur; reset the thermal relay and check its adjustment according to the current in the motor label. If the failure persists, replace the thermal relay. * Fourth, boiler thermostat or pressure switch failure may occur. If there is a problem with the burner thermostats, pressure switches, and steam tank, it may be due to an unadjusted or faulty water level device; adjust it, and if broken, replace it.
E
ericmcdonaldSep 4, 2025
What to do if ECOSTAR Indoor Fireplace flame appears and goes into failure mode?
- M
  Michael FrancoSep 4, 2025
  If the ECOSTAR Indoor Fireplace flame appears and goes into failure mode, it could be due to heavy oil or gas pressure error. Another possible cause is photocell failure; remove and clean it. Also, the program relay might have failed; if so, replace it with a new one.
M
Michelle FrancisSep 6, 2025
How to fix ECOSTAR Indoor Fireplace boiler cover overheating?
- J
  james80Sep 6, 2025
  If the ECOSTAR Indoor Fireplace boiler cover is overheating, it is likely due to a sealing problem. Ensure proper sealing between the boiler cover and the burner. If necessary, use insulating material between the boiler connecting flange and the boiler cover.