EDIFIER STAX SPIRIT S3 User Manual

EN 1. Power ON/OFF
2. Pairing
6. AUX Cable
7. Controls
8. Ear cushion replacement method
1. Power ON: Press and hold the MFB button for 3s when power OFF.
2. Power OFF: Press and hold the MFB button for 3s when power ON.
1. Press and hold the MFB button for 3s when power off. Red and Blue LED
will blink alternately and rapidly.
2. Select "EDIFIER STAX SPIRIT S3" in your device setting to connect. Blue LED
will blink twice per 5s after connected.
Note:
1. For subsequent use, the headset will auto-connect to device used last time.
2. Press and hold the MFB button for 5s when power off to skip the latest
connected device and pair the new Bluetooth device.
3s
3s
3. Reset
1. Power on and disconnected to any Bluetooth devices.
2. Simultaneously press and hold the "+" "-" buttons for 5s to reset and start
Bluetooth pairing.
3. Blue LED will blink 6 times rapidly when successful.
5s
4. Dual Connectivity
5. Charge
1. Pair device A with the headphone. Upon success, disconnect the Bluetooth
of device A or power off the headphone and long press the MFB button of
headphone for 5s to enter the pairing mode.
2. Select "EDIFIER STAX SPIRIT S3" in device B to connect succesfully.
3. Select "EDIFIER STAX SPIRIT S3" in device A to connect manually. Blue LED
will blink twice per 5s when successful.
1. Please connect the product to power source with the included Type-C
charging cable for charging.
2. Red LED is steady lit when charging and off when fully charged.
Input: 5V 1.5A
1. Connect the AUX cable to the headphone when power on, and the
headphone will switch to the AUX in sound source state; connect the
AUX cable to the headphone when power off, the headphone will not
power on automatically, need to press and hold the MFB button for 3s to
turn on.
2. Unplug the AUX cable from the headphone and the headphone will power
off automatically.
3. Green LED is steady lit when in the AUX in sound source state.
x2
x1
x1
x2
x1
x1
x1
x3
Note:
1. : Press and hold.
2. Please do not charge the headset when there is sweat or other liquids
inside the charging port, which may damage the headset.
3. Images are for illustrative purposes only and may differ from the actual
product.
4. Download Edifier Connect App for more customizable control settings.
A B
EDIFIER STAX SPIRIT S3
EDIFIER STAX SPIRIT S3
5s
For more information, please visit our website:
www.edifier.com
@Edifier_Global @Edifier_Global@Edifierglobal
Model: EDF200071
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
www.edifier.com
2022 Edifier International Limited. All rights reserved.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade,
information contained herein may be subject to change from time to
time without prior notice.
Products of EDIFIER will be customized for different applications.
Pictures and illustrations shown on this manual may be slightly
different from actual product.
If any difference is found, the actual product prevails.
Wireless Over-Ear Headphones
S3
Manual

EDIFIER STAX SPIRIT S3 Specifications

General

Driver Type	Planar Magnetic
Bluetooth Version	5.2
Bluetooth Profiles	A2DP, AVRCP, HFP, HSP
Frequency Response	20Hz - 40kHz
Battery Life	80 hours
Battery Life (ANC off)	80 hours
Charging Time	1.5 hours
Active Noise Cancellation (ANC)	No
Ambient Sound Mode	Yes
Microphone	Yes
Water Resistance	No
Foldable Design	Yes
Cable Length	1.2m
Bluetooth Codec	SBC, aptX
Quick Charge	10 minutes for 11 hours playback
Weight	329g
Ear Cushion Material	Leather
Connection Type	3.5mm
Impedance	24 Ohms

Summary

Power ON/OFF

Power Management

Press and hold the MFB button for 3 seconds to power the headphones on or off.

Bluetooth Pairing and Connectivity

Initial Pairing Process

Hold MFB for 3s to activate pairing mode (Red/Blue LED). Connect via device settings.

Auto-Connect and Re-Pairing

Headset auto-connects to the last device. Hold MFB for 5s to skip and pair a new device.

Factory Reset

Resetting the Headphones

Power on, disconnect. Press '+' and '-' simultaneously for 5s to reset and initiate pairing.

Dual Device Connectivity

Connecting Two Devices

Pair with device A, disconnect. Enter pairing mode, connect to device B, then device A manually.

Charging and AUX Cable Usage

Charging Procedure

Connect the Type-C cable to a power source. Red LED is steady when charging, off when full.

AUX Cable Connection

Connect AUX to headphone when power on/off. Power on manually if off. Green LED indicates AUX state.

Controls and Maintenance

Control Function Mapping

Detailed mapping for volume, track skip, play/pause, voice assistant, calls, and gaming modes.

Important Notes and App Usage

Press/hold indicator, charging port warning, image disclaimer, app download for settings.

Ear Cushion Replacement

Visual guide demonstrating the process of removing and replacing ear cushions on the headphones.