EDIFIER NeoBuds Pro 2 User Manual

EN 1. Power ON/OFF
2. Pairing
3. Reset
4. Auto-pause music
5. Charging
6. Controls
True Wireless Noise Cancellation In-Ear Headphones
Manual
Note:
1. Default sound control: high noise cancellation / ambient sound.
2. Default sound modes: music mode / game mode / spatial audio.
3. lmages are for illustrative purposes only and may dier from the
actual product.
4. Download Edier Connect App for more customizable control
settings.
For more information, please visit our website:
www.edier.com
@Edier_Global @Edier_Global@Edierglobal
Model: EDF200113
Edier International Limited
P.O. Box 6264
General Post Oce
Hong Kong
www.edier.com
2023 Edier International Limited. All rights reseed.
Printed in China
NOTICE:
For the need of technical improvement and system upgrade,
information contained herein may be subject to change from time
to time without prior notice.
Products of EDIFIER will be customized for dierent applications.
Pictures and illustrations shown on this manual may be slightly
dierent from actual product. If any dierence is found, the actual
product prevails.
Earbuds
Place earbuds in the charging case and keep the
case closed.
Charging case
1. Please connect the case to power source with the
included Type-C charging cable for charging.
2. LEDs are steady lit when charging and o when
fully charged.
Note:
Please do not charge the earbuds when there is
sweat or other liquids inside the charging po,
which may damage the earbuds.
Input: 5V 200mA(Earbuds)
5V 1A(Charging case)
Indicator
1. Power ON when the case is opened.
2. Power OFF when placed in the case and the case is closed.
Note:
If there is no Bluetooth connection for 2 hours after powered on, the
earbuds will power o automatically.
Indicator
Pairing for the rst time
1. Earbuds placed in the case and keep the case open. LEDs will be
lit one by one from left to right in a circulating pattern.
2. Select "EDIFIER NeoBuds Pro 2" in Bluetooth device setting to
connect. LEDs will blink twice and then turn o when successfully.
Pairing for new device
1. Earbuds placed in the case and keep the case open.
2. Press and hold the button on the case for about 3s. LEDs will be
lit one by one from left to right in a circulating pattern.
3. Select "EDIFIER NeoBuds Pro 2" in Bluetooth device setting to
connect. LEDs will blink twice and then turn o when successfully.
Note:
For subsequent use, the earbuds will automatically connect to the device
used last time.
Fast Pair(Phone with Android 6.0+)
Open the charging case and keep the case next to the phone(make
sure the phone is unlocked and Bluetooth® is on), and tap the pairing
notication when the pop-up window appears to connect eolessly.
Indicator
1. Earbuds placed in the case and keep the case open.
2. Press the button on the case 3 times to re-enter left & right
connection and clear pairing records. LEDs will be lit one by one
from sides to center in a circulating pattern and then will blink
twice when successfully.
3. Select "EDIFIER NeoBuds Pro 2" in Bluetooth device setting to
connect. LEDs will be lit one by one from left to right in a circulating
pattern, then will blink twice and turn o when successfully.
Remove one or both earbuds while listening to music, the music will
automatically pause; to resume the music, inse the earbud(s) back
in the ear(s). This function can be disabled or congured in "wearing
detection" settings via Edier Connect App.
Indicator
Left Tap Panel Right Tap Panel
x2
x3
x2
x2
x2
x2
x2
x3
x3
3s

EDIFIER NeoBuds Pro 2 Specifications

General

Charging Port	USB-C
Frequency Response	20Hz - 40kHz
Transparency Mode	Yes
Controls	Touch controls
Companion App	Edifier Connect
Bluetooth Version	5.3
Bluetooth Profiles	A2DP, AVRCP, HFP
Audio Codecs	SBC, AAC
Water Resistance	IP54
Wireless Charging	Yes