EdilKamin PRESTIGE - User Manual

Questions and Answers

S
Scott DelacruzAug 18, 2025
What to do if my EdilKamin Indoor Fireplace shows 'Failure/Power'?
- R
  Rachael BeckerAug 18, 2025
  If your EdilKamin Indoor Fireplace displays a 'Failure/Power' message, it indicates an electricity failure. Check the electricity connection and for any voltage drops.
R
Robin DavisAug 21, 2025
What to do if my EdilKamin Indoor Fireplace displays 'Stop/Flame'?
- K
  kimberly76Aug 21, 2025
  If your EdilKamin Indoor Fireplace displays 'Stop/Flame', it means there's a drop in smoke temperature. Check for a lack of pellets or too many pellets suffocating the flame in the combustion chamber. Also, check if the maximum thermostat, pressure switch, or water safety thermostat has been activated.
W
wallcourtneyAug 23, 2025
Why is my EdilKamin Indoor Fireplace showing 'smoke °C/high'?
- M
  Mrs. Jessica MasonAug 23, 2025
  If your EdilKamin Indoor Fireplace is showing 'smoke °C/high', it indicates excessive smoke temperature. This may be due to unsuitable pellet type, a smoke extraction anomaly, a blocked smoke channel, incorrect installation, or gear motor drift.
J
jeffery27Aug 26, 2025
What to do if my EdilKamin Indoor Fireplace displays 'Verific./Air Flow'?
- S
  Sandra WardAug 26, 2025
  If your EdilKamin Indoor Fireplace displays 'Verific./Air Flow', it indicates a loss of vacuum. Check if the hatch is open or not properly sealed, if there's an air suction or smoke expulsion problem, if the combustion chamber is clogged, or if the flow sensor is dirty.
E
Edward FrostAug 28, 2025
What to do if my EdilKamin Indoor Fireplace displays 'Block_FI/NO Start'?
- G
  Gregory PowellAug 28, 2025
  If your EdilKamin Indoor Fireplace displays 'Block_FI/NO Start', it means there's an incorrect smoke temperature during ignition. Verify the positioning and cleanliness of the combustion chamber, the functionality of the resistance, and the room temperature. If the room temperature is lower than 3 °C, a fire lighter is needed.
J
James MorganAug 30, 2025
What to do if the pellet DOES NOT enter the crucible of my EdilKamin Indoor Fireplace?
- D
  David MyersAug 30, 2025
  If the pellet does not enter the crucible of your EdilKamin Indoor Fireplace, here are a few things to check: * If the feed screw is empty, fill it by pressing the + and – keys simultaneously. * If pellets are blocked in the hopper, use a vacuum cleaner to empty it. * Check that the feed screw safety thermostat has not overheated, using a tester or a temporary bridge to verify. * Check that the thermal stove contains water, and if the water overheating safety thermostat disconnected the electrical supply, press the button on the back of the thermo-stove to reset it after removing the protective cap.
B
bbyrdSep 1, 2025
What to do if my EdilKamin Indoor Fireplace remote control is not working?
- A
  adiazSep 1, 2025
  If your EdilKamin Indoor Fireplace remote control is not working, try moving closer to the thermal stove or check and replace the battery.
K
kylegarciaSep 3, 2025
What does 'H2O TEMP ALARM' mean on my EdilKamin Indoor Fireplace and what should I do?
- R
  Ryan MurphySep 4, 2025
  If your EdilKamin Indoor Fireplace displays 'H2O TEMP ALARM', it means the water temperature is higher than 90 °C. You should ask the DEALER to activate the ECO function or clean the exchanger pipes, the combustion chamber and the smoke outlet.
S
stephenharringtonSep 6, 2025
What does 'Verific./extract.' mean on my EdilKamin Indoor Fireplace?
- K
  Katrina PadillaSep 6, 2025
  If your EdilKamin Indoor Fireplace displays 'Verific./extract.', it indicates an anomaly detected by the revolution sensor of the smoke extractor motor. Check the smoke extractor functionality, including the connection of the revolution sensor, and inspect the smoke channel for dirt.
A
Anthony SinghSep 8, 2025
How to fix 'Fault/RC' error on EdilKamin Indoor Fireplace?
- J
  Jessica SandersSep 8, 2025
  If your EdilKamin Indoor Fireplace displays 'Fault/RC', it indicates a failure occurring in the thermocouple or it being disconnected. Verify the connection of the thermocouple to the control board and verify functionality in a cold test.