What to do if my EdilKamin Indoor Fireplace shows 'Failure/Power'?
If your EdilKamin Indoor Fireplace displays a 'Failure/Power' message, it indicates an electricity failure. Check the electricity connection and for any voltage drops.
What to do if my EdilKamin Indoor Fireplace displays 'Stop/Flame'?
If your EdilKamin Indoor Fireplace displays 'Stop/Flame', it means there's a drop in smoke temperature. Check for a lack of pellets or too many pellets suffocating the flame in the combustion chamber. Also, check if the maximum thermostat, pressure switch, or water safety thermostat has been activated.
Why is my EdilKamin Indoor Fireplace showing 'smoke °C/high'?
If your EdilKamin Indoor Fireplace is showing 'smoke °C/high', it indicates excessive smoke temperature. This may be due to unsuitable pellet type, a smoke extraction anomaly, a blocked smoke channel, incorrect installation, or gear motor drift.
What to do if my EdilKamin Indoor Fireplace displays 'Verific./Air Flow'?
If your EdilKamin Indoor Fireplace displays 'Verific./Air Flow', it indicates a loss of vacuum. Check if the hatch is open or not properly sealed, if there's an air suction or smoke expulsion problem, if the combustion chamber is clogged, or if the flow sensor is dirty.
What to do if my EdilKamin Indoor Fireplace displays 'Block_FI/NO Start'?
If your EdilKamin Indoor Fireplace displays 'Block_FI/NO Start', it means there's an incorrect smoke temperature during ignition. Verify the positioning and cleanliness of the combustion chamber, the functionality of the resistance, and the room temperature. If the room temperature is lower than 3 °C, a fire lighter is needed.
What to do if the pellet DOES NOT enter the crucible of my EdilKamin Indoor Fireplace?
If the pellet does not enter the crucible of your EdilKamin Indoor Fireplace, here are a few things to check: * If the feed screw is empty, fill it by pressing the + and – keys simultaneously. * If pellets are blocked in the hopper, use a vacuum cleaner to empty it. * Check that the feed screw safety thermostat has not overheated, using a tester or a temporary bridge to verify. * Check that the thermal stove contains water, and if the water overheating safety thermostat disconnected the electrical supply, press the button on the back of the thermo-stove to reset it after removing the protective cap.
What to do if my EdilKamin Indoor Fireplace remote control is not working?
If your EdilKamin Indoor Fireplace remote control is not working, try moving closer to the thermal stove or check and replace the battery.
What does 'H2O TEMP ALARM' mean on my EdilKamin Indoor Fireplace and what should I do?
If your EdilKamin Indoor Fireplace displays 'H2O TEMP ALARM', it means the water temperature is higher than 90 °C. You should ask the DEALER to activate the ECO function or clean the exchanger pipes, the combustion chamber and the smoke outlet.
What does 'Verific./extract.' mean on my EdilKamin Indoor Fireplace?
If your EdilKamin Indoor Fireplace displays 'Verific./extract.', it indicates an anomaly detected by the revolution sensor of the smoke extractor motor. Check the smoke extractor functionality, including the connection of the revolution sensor, and inspect the smoke channel for dirt.
How to fix 'Fault/RC' error on EdilKamin Indoor Fireplace?
If your EdilKamin Indoor Fireplace displays 'Fault/RC', it indicates a failure occurring in the thermocouple or it being disconnected. Verify the connection of the thermocouple to the control board and verify functionality in a cold test.
Details on hopper capacity, efficiency, power output, fuel consumption, and thermal performance.
Lists and describes safety features like thermocouples, vacuum gauges, and thermostats that ensure safe operation.
Specifies minimum distances required from flammable materials for safe installation and fire prevention.
Mandates requirements for air inlets to ensure sufficient combustion air supply, detailing options for direct external air intake.
Details the specifications for the smoke discharge system, including pipe material, sealing, and routing requirements.
Outlines essential start-up procedures to be performed by the dealer, including system checks and initial filling.
Details the mandatory first ignition process, emphasizing the dealer's role in calibration and system checks.
Explains the pellet detection system, how it monitors remaining pellets, and the procedure for initial setup and reloading.
Guide on using the intuitive timer program for setting delayed ignition or shutdown times via the remote control.
Outlines daily cleaning tasks, including agitation of cleaning rods and cleaning the ash pan when the stove is cold.
Lists extensive seasonal maintenance tasks to be performed by an authorized dealer for optimal performance and longevity.
Identifies common causes for stove shutdown and provides solutions, including error codes like H2O PTC_FAULT and Stop/Flame.
Covers additional troubleshooting steps for issues like pellet entry, synoptic panel failure, remote control problems, and water heating.
General| Model | BASIC |
|---|---|
| Brand | EdilKamin |
| Fuel Type | Wood |
| Smoke outlet diameter | 150 mm |
| Glass Door | Yes |
| Air Wash System | Yes |
| Material | Steel |
To Next Page