Why won't my EINHELL Chainsaw start?
If your EINHELL Chainsaw won't start or starts but won't run, possible causes include incorrect starting procedures (refer to the User Manual), an incorrectly adjusted carburetor (have it adjusted by an Authorized Service Center), a fouled spark plug (clean, gap, or replace it), or a plugged fuel filter (replace the fuel filter).
What to do if my EINHELL BG-PC 1235 Chainsaw starts but has low power?
If your EINHELL Chainsaw starts but the engine has low power, check the choke lever position and move it to the RUN position. Also, a dirty air filter can cause this issue; remove, clean, and reinstall the filter. Finally, an incorrectly adjusted carburetor mixture might be the cause, and it should be adjusted by an Authorized Service Center.
Why does my EINHELL BG-PC 1235 Chainsaw smoke so much?
If your EINHELL Chainsaw smokes excessively, the issue may be an incorrect fuel mixture. Use properly mixed fuel (40:1 mixture).
What to do if my EINHELL BG-PC 1235 Chainsaw engine dies?
If the engine of your EINHELL Chainsaw dies, the possible causes are: the petrol tank is empty (fill it up), the fuel filter is in the wrong position in the tank (completely fill the petrol tank or re-position the fuel filter in the petrol tank).
Why does my EINHELL Chainsaw engine hesitate?
If your EINHELL Chainsaw engine hesitates, it might be due to an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
How to improve the performance of my EINHELL BG-PC 1235 Chainsaw?
If your EINHELL Chainsaw demonstrates poor performance when operated, the cause may be a blunt or loose chain. Sharpen or replace the chain and tension the chain.
Why does my EINHELL BG-PC 1235 Chainsaw have no power under load?
If your EINHELL Chainsaw has no power under load, the spark plug may be incorrectly gapped. Clean, gap, or replace the plug.
Why is my EINHELL BG-PC 1235 running erratically?
If your EINHELL Chainsaw runs erratically, the cause may be an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
What causes insufficient chain lubrication in my EINHELL BG-PC 1235 Chainsaw?
If your EINHELL Chainsaw has insufficient chain lubrication and the cutter rail and chain get hot, possible causes are: the oil tank for the chain is empty (top it up), oil lubrication openings moved (clean the oil lubrication hole in the cutter bar, clean the groove in the cutter bar).
Describes the different parts and components of the chainsaw.
Explanation of key safety mechanisms and their functions.
Defines the intended applications and operational limits of the equipment.
Step-by-step guide for attaching the guide bar to the chainsaw.
Instructions for properly mounting the saw chain onto the bar.
Procedure for setting and adjusting the correct chain tension.
How to test the chain brake's functionality and safety.
Guidance on mixing fuel and essential chain lubrication procedures.
Detailed steps for safely starting the chainsaw engine.
Procedure for re-starting the engine when it is already warm.
Methods for safely shutting down the chainsaw.
Guides for felling trees and bucking logs.
Procedures for cleaning the chainsaw after use.
Testing the chain brake's functionality.
Instructions for cleaning or replacing the air filter.
Guidance on servicing or replacing the fuel filter.
Maintenance steps for the spark plug.
Adjusting the carburetor for optimal performance.
Lubrication and care for the guide bar and sprocket.
Sharpening, tensioning, and breaking in the saw chain.
Proper procedures for storing the chainsaw.
Information on how to order necessary spare parts.
General| Motor type | 2-stroke motor |
|---|---|
| Chain speed | 21 m/s |
| Automatic oiling | Yes |
| Chain bar length | 320 mm |
| Oil tank capacity | 0.21 L |
| Fuel tank capacity | 0.31 L |
| Engine displacement | 37.2 cm³ |
| Power source | Gasoline |
To Next Page