EINHELL GC-PC 1335/1 I User Manual (English)

Questions and Answers:

P
Philip HenryAug 14, 2025
Why won't my EINHELL GC-PC 1335/1 I start?
- J
  James BrownAug 14, 2025
  There are several reasons why your EINHELL Chainsaw might not start. It could be due to incorrect starting procedures. Refer to the User Manual for the correct procedure. Another cause might be too much fuel in the combustion chamber from failed start attempts; in this case, wait about 30 minutes for the fuel to evaporate before trying again. Other potential issues include a fouled spark plug (clean, gap, or replace it), a plugged fuel filter (replace it), or an incorrect carburetor mixture adjustment setting (have it adjusted by an Authorized Service Center).
J
jenniferthomasAug 17, 2025
What to do if EINHELL GC-PC 1335/1 I Chainsaw engine has low power?
- T
  teresaaustinAug 17, 2025
  If your EINHELL Chainsaw engine has low power, check the choke lever position and move it to the correct position. Also, a dirty air filter can cause this issue; remove, clean, and reinstall the filter. Finally, an incorrect carburetor mixture adjustment setting may be the cause; have it adjusted by an Authorized Service Center.
A
Adrian MorganAug 20, 2025
What to do if EINHELL Chainsaw engine dies?
- A
  Ashley ScottAug 20, 2025
  If your EINHELL Chainsaw engine dies, check if the petrol tank is empty and fill it up. Also, the fuel filter's position in the tank might be incorrect. Completely fill the petrol tank or reposition the fuel filter.
J
juliecampbellAug 25, 2025
Why EINHELL GC-PC 1335/1 I has poor performance?
- D
  Dawn RuizAug 25, 2025
  Poor performance of your EINHELL Chainsaw can be attributed to a blunt chain, which requires sharpening or replacement. Alternatively, a loose chain could be the cause, and you should tension the chain.
S
Sarah WilliamsAug 27, 2025
Why EINHELL Chainsaw smokes excessively?
- B
  barbara42Aug 27, 2025
  If your EINHELL Chainsaw smokes excessively, it's likely due to an incorrect fuel mixture. Ensure you are using properly mixed fuel (40:1 mixture).
G
Gail BakerAug 30, 2025
What to do if EINHELL GC-PC 1335/1 I Chainsaw chain lubrication is insufficient?
- M
  Maria DickersonAug 30, 2025
  If your EINHELL Chainsaw experiences insufficient chain lubrication, and the cutter rail and chain get hot, first check if the oil tank for the chain is empty and top it up. Another possible cause is oil lubrication openings moved; clean the oil entry hole/groove on the guide rail.
C
chadmitchellSep 3, 2025
What to do if EINHELL GC-PC 1335/1 I engine hesitates?
- M
  matthewhowardSep 3, 2025
  If your EINHELL Chainsaw engine hesitates, the cause may be an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
R
Richard StewartSep 6, 2025
Why EINHELL GC-PC 1335/1 I runs erratically?
- A
  Angelica KingSep 6, 2025
  If your EINHELL Chainsaw runs erratically, it may be due to an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
S
Stacey OlsenSep 10, 2025
What to do if EINHELL GC-PC 1335/1 I has no power under load?
- D
  Dennis PaceSep 10, 2025
  If your EINHELL Chainsaw has no power under load, it could be due to an incorrectly gapped spark plug. Clean, gap, or replace the spark plug.

EINHELL GC-PC 1335/1 I Specifications

General

Idle speed	11500 RPM
Motor type	2-stroke motor
Blade length	350 mm
Cutting speed	21.9 m/s
Product color	Black, Red
Cutting length	345 mm
Automatic oiling	Yes
Oil tank capacity	0.17 L
Fuel tank capacity	0.3 L
Brand compatibility	Einhell
Engine displacement	37.2 cm³
Power source	Gasoline