EINHELL GC-PC 1335 TC

Questions and Answers

K
Kevin AtkinsonAug 15, 2025
Why won't my EINHELL Chainsaw start?
- T
  Tracy WheelerAug 15, 2025
  There are several reasons why your EINHELL Chainsaw might not start. It could be due to incorrect starting procedures. Refer to the User Manual for the correct procedure. Another cause might be too much fuel in the combustion chamber from failed start attempts; in this case, wait about 30 minutes for the fuel to evaporate before trying again. Other potential issues include a fouled spark plug (clean, gap, or replace it), a plugged fuel filter (replace it), or an incorrect carburetor mixture adjustment setting (have it adjusted by an Authorized Service Center).
M
Melissa OconnorAug 18, 2025
What to do if EINHELL GC-PC 1335 TC engine has low power?
- H
  hollyvelasquezAug 18, 2025
  If your EINHELL Chainsaw engine has low power, check the choke lever position and move it to the correct position. Also, a dirty air filter can cause this issue; remove, clean, and reinstall the filter. Finally, an incorrect carburetor mixture adjustment setting may be the cause; have it adjusted by an Authorized Service Center.
D
Donald MillsAug 21, 2025
Why EINHELL GC-PC 1335 TC smokes excessively?
- D
  Danielle SalazarAug 21, 2025
  If your EINHELL Chainsaw smokes excessively, it's likely due to an incorrect fuel mixture. Ensure you are using properly mixed fuel (40:1 mixture).
J
Joseph PerryAug 25, 2025
What to do if EINHELL GC-PC 1335 TC engine dies?
- K
  Kevin MillerAug 26, 2025
  If your EINHELL Chainsaw engine dies, check if the petrol tank is empty and fill it up. Also, the fuel filter's position in the tank might be incorrect. Completely fill the petrol tank or reposition the fuel filter.
C
Christopher GoodwinAug 28, 2025
Why EINHELL GC-PC 1335 TC has poor performance?
- C
  Carl BallAug 28, 2025
  Poor performance of your EINHELL Chainsaw can be attributed to a blunt chain, which requires sharpening or replacement. Alternatively, a loose chain could be the cause, and you should tension the chain.
B
Brooke AndersonSep 1, 2025
What to do if EINHELL GC-PC 1335 TC chain lubrication is insufficient?
- A
  Alexander PrattSep 1, 2025
  If your EINHELL Chainsaw experiences insufficient chain lubrication, and the cutter rail and chain get hot, first check if the oil tank for the chain is empty and top it up. Another possible cause is oil lubrication openings moved; clean the oil entry hole/groove on the guide rail.
C
Courtney BauerSep 4, 2025
What to do if EINHELL Chainsaw engine hesitates?
- P
  patricia42Sep 4, 2025
  If your EINHELL Chainsaw engine hesitates, the cause may be an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
J
Julia GarrettSep 7, 2025
Why EINHELL GC-PC 1335 TC runs erratically?
- J
  Joseph AtkinsonSep 7, 2025
  If your EINHELL Chainsaw runs erratically, it may be due to an incorrect carburetor mixture adjustment setting. Have the carburetor adjusted by an Authorized Service Center.
A
Andrea KellerSep 12, 2025
What to do if EINHELL GC-PC 1335 TC Chainsaw has no power under load?
- J
  Jacqueline WeberSep 12, 2025
  If your EINHELL Chainsaw has no power under load, it could be due to an incorrectly gapped spark plug. Clean, gap, or replace the spark plug.