EINHELL GC-PC 930 I - User Manual

Questions and Answers

M
Meredith WallAug 15, 2025
Why my EINHELL GC-PC 930 I Chainsaw won't start?
- P
  Paul RussellAug 15, 2025
  If your EINHELL Chainsaw won't start or starts but won't run, there might be several reasons. First, ensure you are following the correct starting procedures as outlined in the User Manual. If you've flooded the combustion chamber with too much fuel from repeated starting attempts, wait about 30 minutes for the fuel to evaporate before trying again. Other potential causes include a fouled spark plug (clean, gap, or replace it), a plugged fuel filter (replace it), or an incorrect carburetor mixture adjustment setting (have it adjusted by an Authorized Service Center).
W
wlindseyAug 18, 2025
How to improve the performance of my EINHELL GC-PC 930 I?
- K
  Kelly GloverAug 18, 2025
  If you experience poor performance when operating your EINHELL Chainsaw, check the following: - Ensure the chain is sharp. Sharpen or replace the chain if it is blunt. - Check the chain tension. Tension the chain if it is loose.
D
Danielle SmithAug 21, 2025
What to do if my EINHELL GC-PC 930 I has insufficient chain lubrication?
- N
  nicolesharpAug 22, 2025
  If you notice insufficient chain lubrication causing the cutter rail and chain to get hot on your EINHELL Chainsaw, first check if the oil tank for the chain is empty and top it up if necessary. Also, inspect the oil lubrication openings and clean the oil entry hole/groove on the guide rail if they are obstructed.
J
John WagnerAug 25, 2025
What to do if my EINHELL Chainsaw engine dies?
- C
  Courtney BrayAug 26, 2025
  If your EINHELL Chainsaw engine dies, it could be due to an empty petrol tank, so fill it up. Another reason might be that the fuel filter is in the wrong position in the tank. In this case, completely fill the petrol tank or re-position the fuel filter in the petrol tank.
R
Raymond MorrisAug 28, 2025
Why is my EINHELL GC-PC 930 I Chainsaw smoking so much?
- G
  gregorychristineAug 28, 2025
  If your EINHELL Chainsaw is smoking excessively, the cause may be an incorrect fuel mixture. Make sure you are using properly mixed fuel (40:1 mixture).
R
Ralph SalazarAug 31, 2025
Why does my EINHELL Chainsaw start, but engine has low power?
- R
  rjarvisAug 31, 2025
  If your EINHELL Chainsaw starts but the engine has low power, check the choke lever position and ensure it is correct. Also, a dirty air filter can cause this issue, so remove, clean, and reinstall the filter. If these steps don't resolve the problem, the carburetor mixture adjustment setting may be incorrect; have it adjusted by an Authorized Service Center.
S
Scott CurtisSep 4, 2025
Why my EINHELL GC-PC 930 I runs erratically?
- T
  tom58Sep 4, 2025
  If your EINHELL Chainsaw is running erratically, the carburetor mixture adjustment setting may be incorrect. Have the carburetor adjusted by an Authorized Service Center.
B
Bonnie WilliamsSep 7, 2025
Why does my EINHELL GC-PC 930 I engine hesitates?
- P
  Patricia MurraySep 7, 2025
  If your EINHELL Chainsaw engine hesitates, the carburetor mixture adjustment setting may be incorrect. Have it adjusted by an Authorized Service Center.
C
Curtis GreenSep 10, 2025
What to do if my EINHELL GC-PC 930 I Chainsaw has no power under load?
- D
  Daniel HoffmanSep 12, 2025
  If your EINHELL Chainsaw has no power under load, it could be due to an incorrectly gapped spark plug. Clean, gap, or replace the plug.

Summary

Safety Regulations

Proper Use

Technical Data

Before Starting the Equipment

5.1 Installing the Guide Rail and Saw Chain

Step-by-step guide for fitting the chain bar and saw chain onto the chainsaw.

5.2 Adjusting the Chain Tension

Instructions on how to properly tension the saw chain for safe operation.

Operation

6.1 Chain Brake

Details on the function and checking procedures for the chainsaw's chain brake system.

6.1.2 Checking the Clutch

Instructions for performing a functional check on the chainsaw's clutch mechanism.

6.2 Starting a Cold Engine

Step-by-step guide for starting the chainsaw engine when it is cold.

6.3 Starting a Warm Engine

Instructions for starting the chainsaw engine when it has recently been used.

6.4 To Stop Engine

Cleaning, Maintenance, Storage and Spare Parts

7.2 Maintenance

7.2.6 Chain Maintenance

Troubleshooting Guide

EINHELL GC-PC 930 I Specifications

General

Power	0.9 kW
Bar Length	30 cm
Chain Speed	21 m/s
Engine Displacement	25.4 cm³
Power Source	Gasoline
Chain Pitch	3/8"
Chain Gauge	1.3 mm
Fuel Tank Capacity	230 mL
Oil Tank Capacity	160 mL