EINHELL GC-RS 60 CB User Manual

GB
- 7 -
warranty.
•
Keep the air vents clear of dirt.
•
After use, unplug the machine and check it for
damage.
•
When you are not using the shredder, keep it
in a dry place out of the reach of children.
•
Check the screws regularly to see that they
are properly tightened.
•
The mains voltage must be the same as the
voltage specified on the rating plate.
•
Power cables used with the shredder must
not be of a lighter duty class than HO7RN-F
rubber-insulated flexible cables according
to DIN 57282/ VDE 0282 with a minimum
diameter of 1.5 mm
2
. Plug connectors must
be equipped with earthing contacts and the
coupling must be rain-water-protected.
•
Use only original replacement parts for repair
and maintenance purposes.
•
Have repairs carried out only by a qualified
electrician.
•
Examine the shredder for signs of wear or
damage each time before you use it and after
any collisions. Have essential repairs carried
out without delay.
•
Never use replacement parts or accessories
which are not foreseen or recommended by
the manufacturer.
•
Pull out the power plug before carrying out
any inspection, cleaning or other work on the
shredder and whenever it is not being used.
•
Before you begin your work, examine the
material you want to shred. Remove any for-
eign bodies. Continue to watch out for foreign
bodies while you are working. If you come
across any foreign bodies while shredding,
shut down the machine and remove the items
in question.
•
Keep the machine away from other persons,
particularly children and pets.
•
Use the machine only in the way described in
these operating instructions.
•
The electric circuit must be protected at least
by a 16A fuse.
•
The efficiency of the machine will be greatly
reduced if a connecting cable with too small
a cross section is used. A conductor cross
section of at least 3x1.5 mm
2
is required for
cables up to 25 m long, and one of at least
3x2.5 mm
2
for cables longer than 25 m.
•
If the machine has to be lifted for transporting,
be sure to switch off the motor first and wait
for the cutter to come to a standstill. Each
time before you leave the machine, switch off
the motor and pull out the power plug. Before
you connect the machine to the power supply,
make sure that the loading funnel is properly
connected to the motor housing and the re-
lease screw tightened.
•
If the garden refuse shredder vibrates ex-
cessively, turn off the motor, pull out the
power plug, and find out immediately what is
causing the vibrations. Intensive vibration is
usually a sign that something is wrong.
•
Do not wear loose clothing or clothing with
hanging belts or cords.
•
Do not use the machine on a paved area that
has been graveled where discharged material
may cause injuries.
•
Ensure that the loading funnel inlet is empty
before you start the machine.
•
Keep your head and body away from the in-
feed opening.
•
Do not move your hands, other body parts or
clothing into the infeed chamber, ejector chu-
te or near other moving parts.
•
Make sure that you are balanced and stan-
ding on a firm surface at all times. Do not
stretch forwards. Never stand higher than the
machine when feeding material into it.
•
Keep away from the discharge zone when
you start the machine.
•
If foreign bodies get into the cutting tool or
the machine generates unusual noises or
vibrates in a strange way, switch off the motor
immediately and allow the machine to come
to a standstill. Pull the plug and carry out the
following work:
- Check the machine for signs of damage
- Check that all the parts are secure and tigh-
ten them if necessary.
- Have any damaged parts replaced or re-
paired, but use only spare parts of the same
type and equivalent quality
•
If the machine is blocked switch off the motor
and pull the plug before you start the cleaning
procedure. Ensure that the motor is clear of
waste and other accumulations to protect the
motor from suffering damage or possibly cat-
ching fire.
•
Ensure that all the covers and guards are in
position and in good working order.
•
Do not tip the machine whilst the motor is run-
ning.
•
Switch off the machine before you fit or remo-
ve the collection container.
•
The tool may only be used outdoors (i.e. not
in the vicinity of a wall or any other ridged ob-
ject)
•
Damaged or illegible labels must be replaced
Anl_GC_RS_60_CB_GB_Korea.indb 7Anl_GC_RS_60_CB_GB_Korea.indb 7 07.02.2023 09:17:4607.02.2023 09:17:46

EINHELL GC-RS 60 CB Specifications

General

Brand	EINHELL
Model	GC-RS 60 CB
Category	Paper Shredder
Language	English