EINHELL NHR 130 - User Manual

Questions and Answers

C
Chad BennettAug 16, 2025
Why is there a loss of pressure in my EINHELL Pressure Washer?
- R
  Randall RushAug 16, 2025
  If your EINHELL Pressure Washer experiences a loss of pressure, the issue might stem from several causes. The nozzle could be worn, or the valves might be dirty or clogged. Additionally, the valve seals or other seals could be worn, and the filter might be clogged. To address this, try changing the nozzle. Also, check, clean, or replace the valves, valve seals, and other seals as needed, and inspect and clean the filter.
D
Danny McculloughAug 22, 2025
What to do if my EINHELL NHR 130 motor suddenly stops?
- A
  Alicia RoweAug 22, 2025
  If the motor of your EINHELL Pressure Washer suddenly stops, it could be due to the thermal relay being triggered by overheating. To resolve this, check the voltage. Turn off the switch and allow the motor to cool down for a few minutes.
D
David PotterAug 26, 2025
Why is my EINHELL NHR 130 making excess noise?
- S
  sherylwilsonAug 26, 2025
  Excess noise in your EINHELL Pressure Washer can be attributed to several factors. Air may be getting drawn in, or the valves might be worn, dirty, or clogged. The bearings could also be worn, the water temperature might be too high, or the filter might be dirty. Check the intake lines, and inspect, clean, or replace the valves. Also, check and/or exchange the bearings. Lower the water temperature to below 60 °C and inspect and/or exchange the filter.
S
Shannon PerryAug 28, 2025
What to do if EINHELL NHR 130 pump runs but doesn't generate pressure?
- P
  Pamela SmithAug 28, 2025
  If the electric pump runs but no pressure is generated in your EINHELL Pressure Washer, it could be due to a clogged intake filter, air being drawn in at the connectors, clogged or worn inlet and outlet valves, or the nozzle hole diameter being too large. Clean the filter, check the intake connection fitting and hose connectors. Clean or replace the valves. Check and replace the nozzle.
K
Kimberly BrownAug 31, 2025
Why is the operating pressure of my EINHELL NHR 130 Pressure Washer irregular?
- M
  moorechrisAug 31, 2025
  Irregular operating pressure in your EINHELL Pressure Washer can occur if air is being drawn in, or if the valves are clogged and worn, or if the seals are worn. Inspect the intake connectors. Clean and replace the valves. Check and replace the seals.
B
Brian DavisSep 3, 2025
Why is water leaking from the pump head of my EINHELL NHR 130 Pressure Washer?
- K
  Kelly LiuSep 3, 2025
  If water leaks from the pump head of your EINHELL Pressure Washer, it's likely due to worn seals or a worn O-ring in the seal set. Exchange the seal. Exchange the O-ring.
A
Andrew GuerreroSep 6, 2025
What to do if my EINHELL NHR 130 Pressure Washer motor hums but doesn't start?
- S
  Sara SilvaSep 6, 2025
  If, when you press the switch on your EINHELL Pressure Washer, the motor hums but doesn't start, it could be due to several reasons: the mains voltage might be lower than specified, the pump could be blocked or frozen, or the extension cable might be insufficient (either the cross section is too small, or the cable is too long). Check to see that the extension cable is sufficient and exchange the extension cable for one that is sufficient.
L
Lisa DiazSep 9, 2025
Why is the water from my EINHELL Pressure Washer mixed with oil?
- C
  Cheyenne RichmondSep 9, 2025
  If the expelled water from your EINHELL Pressure Washer is mixed with oil, it indicates that the sealing rings (water + oil) are worn. Check and/or exchange them.
M
Matthew MorenoSep 10, 2025
How to troubleshoot an EINHELL Pressure Washer when the electric pump doesn't start?
- D
  Debbie MartinSep 12, 2025
  If your EINHELL Pressure Washer's electric pump isn't running when you press the switch, several factors could be at play. The plug might be damaged, there could be insufficient voltage, the pump might be locked, or the thermal relay could have triggered. Check the plug and fuses to ensure they're in good condition. Manually turn over the motor. Allow the motor to cool down.
K
Kristy CarterSep 12, 2025
Why is my EINHELL Pressure Washer pump dripping?
- E
  Erica ReyesSep 12, 2025
  If your EINHELL Pressure Washer pump is dripping, it is likely due to worn seals. Check and replace them, preferably at a professional repair shop.