EasyManuals Logo

EINHELL TC-ID 18 Li User Manual

EINHELL TC-ID 18 Li
42 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
EN
- 11 -
3. Intended use
The impact drill is designed for drilling holes into
wood, iron and non-ferrous metals, and for impact
drilling in stone, using the appropriate bits.
The equipment is not designed for tightening
screws of any kind.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................18 V
No-load speed: ......................... 2600 rpm (min
-1
)
Clockwise/counter-clockwise: ........................yes
Clamping range
of drill chuck: ......................... max. ½ in. (13 mm)
Impact Speed: .................................... 41600 bpm
Drilling capacity:
Concrete : ..................................... ½ in. (13 mm)
Metal: ............................................. in. (10 mm)
Wood: ..............................................1 in. (25 mm)
Weight (Tool only): ........................3.5 lbs (1.6 kg)
Wear ear-mu s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect
condition.
Maintain and clean the equipment regularly.
Adapt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment‘s construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched o and times in which
the tool is switched on but operates without load).
5. Before starting the equipment
5.1. Fitting the additional handle
(Fig. 2-3/Item 7)
The additional handle (7) enables you to achieve
better stability whilst using the impact drill. Do not
use the tool without the additional handle.
The additional handle (7) is secured to the impact
drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
The supplied additional handle (7) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the impact drill.
After you have positioned the additional
handle (7), turn it to the most comfortable
working position for you.
Now turn the handle in the opposite direction
again until the additional handle is secure.
The additional handle (7) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop (Fig.
4/Item 2)
The depth stop (2) is held in place by the
additional handle (7) by clamping. The clamp can
be released and tightened by turning the handle.
Release the clamp and fit the depth stop (2)
Anl_TC_ID_18_Li_SPK7_USA.indb 11Anl_TC_ID_18_Li_SPK7_USA.indb 11 10.09.2021 09:18:4010.09.2021 09:18:40

Other manuals for EINHELL TC-ID 18 Li

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the EINHELL TC-ID 18 Li and is the answer not in the manual?

EINHELL TC-ID 18 Li Specifications

General IconGeneral
BrandEINHELL
ModelTC-ID 18 Li
CategoryDrill
LanguageEnglish

Related product manuals