Electrolux EHC644BA - User Manual

Questions and Answers

M
Megan OrtizAug 12, 2025
What to do if Electrolux Hob cooking zones won't switch on?
- C
  Charles SuttonAug 12, 2025
  If your Electrolux Hob cooking zones won't switch on or aren't working, it could be due to several reasons. First, ensure that no more than 10 seconds have passed since you switched on the appliance; if so, switch it on again. Also, check if the child safety device or the lock is activated and deactivate them accordingly, referring to the "Child safety device" and "Locking/unlocking the control panel" sections for guidance. Make sure you are only touching one sensor field at a time. Finally, automatic switch-off may have been triggered. Remove any objects from the control panel and switch the hob on again.
A
Amber SanchezAug 16, 2025
How to clean red rings and stains from Electrolux EHC644BA ceramic glass cooktop?
- S
  sarah28Aug 16, 2025
  If you notice red rings, limescale or water rings, shiny metallic or other discoloration, scratches/shadows, bubbles, or other marks on your Electrolux Hob's ceramic glass cooktop, it's likely due to improper cleaning. To resolve this, use a ceramic glass cleaner such as Cerapol to clean the surface correctly.
B
Bradley BlackburnAug 20, 2025
Why does my Electrolux EHC644BA Hob make noise when turned off?
- S
  Stephanie RussellAug 20, 2025
  If your Electrolux Hob is emitting an acoustic signal when switched off, it's likely because the control panel is covered by objects. Remove any objects from the control panel to stop the signal.
Y
ynelsonAug 25, 2025
What to do if Electrolux EHC644BA Hob turns on and off with acoustic signal?
- E
  Eileen LiAug 25, 2025
  If your Electrolux Hob displays an acoustic signal and switches itself on and off, followed by another acoustic signal after 5 seconds, it indicates that the On/Off sensor field is covered. Ensure that no objects are placed on the control panel to prevent this issue.
T
Timothy HernandezAug 27, 2025
Why is warm up function on my Electrolux EHC644BA not working?
- J
  josephpetersonAug 27, 2025
  If the automatic warm-up function on your Electrolux Hob isn't activating, it could be due to a few reasons. First, if there's still residual heat on the cooking zone, allow it to cool down. Also, the highest heat setting has the same power as the automatic warm-up function. If the heat setting was set using the sensor field, switch off the cooking zone and set it again using the sensor field.
L
Laura JohnsonAug 31, 2025
Why is the residual heat indicator not on for my Electrolux EHC644BA Hob?
- K
  Kristen SuttonAug 31, 2025
  If the residual heat indicator on your Electrolux Hob isn't displaying anything, it might be because the cooking zone was only on for a short time and isn't hot enough. If the cooking zone is supposed to be hot, it is recommended to call the Customer Service Department.
T
Taylor DaltonSep 4, 2025
What does it mean when is lit on Electrolux EHC644BA?
- J
  John MooreSep 4, 2025
  If the symbol is lit on your Electrolux Hob, it indicates that the overheating protection for the cooking zone or automatic switch off has been triggered. To resolve this, switch off the cooking zone and then switch it on again.
V
Virginia VaughnSep 7, 2025
What to do if Electrolux EHC644BA Hob displays and number?
- S
  Sharon PetersSep 8, 2025
  If you Electrolux Hob displays and a number, it indicates an electronics fault. Disconnect the appliance from the electrical supply for a few minutes by removing the fuse. If the issue persists after switching it back on, contact customer service.

Summary

Safety Information

General, Use, and Childrens Safety

Covers fundamental safety rules, correct usage, and child protection.

Safety During Use and Cleaning

Details precautions during operation and safe cleaning methods.

Operating Instructions

Basic Operations

How to turn on/off, set heat, manage rings, and lock the panel.

Troubleshooting

Surface and Zone Issues

Solutions for problems related to the cooktop surface and zone functionality.

Control, Signal, and Error Issues

How to resolve issues with the control panel, signals, and error codes.

Installation and Assembly

Installation Safety and Electrical

Safety warnings, electrical connection, and general installation advice.

Sealing and Fitment