Electrolux EOEM61CS - Installation

installation electrolux e:line ovens 3332 electrolux e:line ovens installation
warning
Please follow the points below when installing the appliance
Useanauthorisedperson
• Asstatedinthelocalmunicipalbuildingcodesand
other relevant statutory regulations:
• WiringconnectionsmustbeinaccordancewithAS/NZS
3000WiringRulesandanyparticularconditionsofthe
local authority.
• Refertodataplateforratinginformation.Thedata
plate is positioned behind the bottom of the oven door.
The circuit diagram is positioned on the top panel of
the appliance.
• Forapplianceswithopencookingsurfaces,anallpole
disconnect functional switch should be provided near
theapplianceinanaccessibleposition.RefertoAS/
NZS3000clause4.7.1
• Wiringshouldbeprotectedagainstmechanicalfailure.
RefertoAS/NZS3000clauses3.3.2.6,3.9,3.10
• Ameansofdisconnectionwithacontactseparationof
at least 3mm must be supplied in the fixed wiring.
warning
Thisappliancemustbeproperlyearthed.
• Donotlifttheappliancebythedoorhandles.
• Preparethecupboardopeningtomatchyourappliance
measurements. (See diagrams)
• Slideapplianceintothecupboard,ensuringthatthe
supply cable (where fitted) does not kink.
• Topreventtipping,usethescrewssuppliedtosecure
your oven into the cupboard by fastening through the
2 holes to the front panel.
• Wheretheapplianceisbuiltintoacabinet,thecabinet
mustbecapableofwithstanding70°C.Installationinto
lowtemperaturetolerantcabinetry(e.g.Vinylcoated)
may result in deterioration of the low temperature
coating by discolouring or bubbling.
• Iftheapplianceistobeinstalledadjacenttovinyl
wrapped surfaces, use an installation kit available from
thevinyl-wrapsupplier.
• ElectroluxHomeProductscannotacceptresponsibility
for damage caused by installation into low temperature
tolerant cabinets.
• Afterinstallation,testandensurethattheappliance
operates correctly before handing it over to the
customer.

 


warning
To avoid any potential hazard, you must follow our
instructionswhenyouinstallyourappliance.Failure
to install the appliance correctly could invalidate any
warrantyorliabilityclaimsandleadtoprosecution.
Installation
Cabinet construction for your appliance
For the best integration within a kitchen, install this appliance
inastandard600mmwidecupboardthatgivesausht
withthesurroundingcupboardfronts.Itcanalsobeinstalled
using a proud fit.
FlushFit
16mm
568mm
600mm
20mm
Inll
panel
Cupboard
door
Oven
100mm
max for
Pyro oven
ProudFit
16mm
568mm
600mm
Inll
panel
Cupboard
door
Oven
100mm
max for
Pyro oven
Note:


Underbenchoven
Your underbench oven looks best when the control panel
isdirectlyunderthebenchtop.Anupperinllpanelmay
be added if the cooktop placed above the benchtop is too
deep. Refer to cooktop installation instructions for required
clearance between cooktop and oven.
Cut-out dimensions
type of fit A(width) B(height) C(depth)
Flush fit (mm) 600 600 581min.
Proud fit (mm) 568 590 560min.
A
C
B
561mm
mounting holes
583mm
596mm
DuoovenCut-outdimensions
type of fit A(width) B(height) C(depth)
Flush fit (mm) 600 893 581min.
Proud fit (mm) 568 885 560min.
min. 650mm
A
561mm
mounting
holes
mounting holes
596mm
456mm
B
C
DoubleovenCut-outdimensions
type of fit A(width) B(height) C(depth)
Flush fit (mm) 600 1086 581min.
Proud fit (mm) 568 1078 560min.
min. 650mm
561mm
mounting
holes
A
B
C
mounting holes
596mm
456mm