5
24 Open the front cover and lift out the
insert holding the s-bag
®
.
28 Pull the filter(s) holder upwards
until coming away from the groove.
Carefully pull the old, dirty filter(s) out
of the filter holder and replace with a
new filter(s).
29 Reattach the filter holder containing
the new filter(s).
27 Replace the insert holding the s-bag
®
and then close the cover.
B Model with exhaust filter Follow steps
24, 28 and replace old motor-filter
with a new one. Then follow steps 29,
27.
Replacement of the exhaust filter*
There are three types*** of exhaust filter:
• Microfilter* (Ref. No. EF 17)
• Hepa H12* non washable (Ref. No. EF
H12)
• Hepa H12*/*** washable (Ref. No. EF
H12W)
The filters must always be replaced with
new ones and cannot be washed (if not
mentioned).
30 Place your thumbs on the back edge
of the lid and then open the lid by
pulling the handle backwards and
upwards with your index/middle fin-
ger.
31 Lift out the filter. Insert a new filter
and replace the lid as shown.
Cleaning the hose and nozzle
The vacuum cleaner stops automatically
if the nozzle, tube, hose or filters and
s-bag
®
becomes blocked. In such cases,
disconnect from mains and allow to cool
for 20-30 minutes. Clear blockage and/or
replace filters and s-bag
®
and restart.
Tubes and hoses
34 Use a cleaning strip or similar to clear
the tubes and hose.
3* Hose handle could be dismantled
from hose if cleaning is needed.
35 It may also be possible to remove the
obstruction in the hose by squeez-
ing it. However, be careful in case
the obstruction is caused by glass or
needles caught inside the hose.
Note: The warranty does not cover any dam-
age to the hose caused by cleaning it.
Cleaning the floor nozzle
39 To avoid deterioration of suction
power, frequently clean the carpet/
hard floor nozzle. The easiest way to
clean it is by using the hose handle.
36* Press each wheel-hub and draw away
the wheels. Use the crevice nozzle to
clean the wheel axles. Remove dust-
balls, hair or other objects that may
be entangled. Replace the wheel by
pressing them onto the axles.
37* Larger objects can be accessed by
removing the connection hose from
the nozzle (press the small catches
located on each side and simultane-
ously draw the connection tube out-
wards in an upright position).
38* Remove the object(s) and replace the
connection hose.
Cleaning the turbo nozzle*
40 Disconnect the nozzle from the
vacuum cleaner tube and remove
entangled threads, etc. by snipping
them away with scissors. Use the
hose handle to clean the nozzle.
Troubleshooting
The vacuum cleaner does not start
• Check that the cable is connected to
the mains.
• Check that the plug and cable are not
damaged.
• Check for a blown fuse.
The vacuum cleaner stops
• Check whether the dust bag, s-bag
®
is full. If so, replace it with a new one.
• Is the nozzle, tube or hose blocked?
• Are the filters blocked?
Water has entered the vacuum cleaner
It will be necessary to replace the motor
at an authorised Electrolux service cen-
tre. Damage to the motor caused by the
penetration of water is not covered by the
warranty.
Consumer information
Electrolux decline all responsibility for all
damages arising from any improper use
of the appliance or in cases of tampering
with the appliance.
This product is designed with the environ-
ment in mind. All plastic parts are marked
for recycling purposes. For details see our
web site: www.electrolux.com
If you have any comments on the cleaner
or the Instructions for Use booklet please
e-mail us at: floorcare@electrolux.com
If you can´t find dustbags or accessories to your
Electrolux vacuum cleaner, please visit our website at
www.electrolux.com.
To Next Page
Loading...
