Electrolux EWFLW65H User Manual (English)

Other manuals for Electrolux EWFLW65H

Questions and Answers:

J
johngutierrezAug 31, 2025
Why Electrolux EWFLW65H water does not enter or enters slowly?
- S
  Sarah ButlerAug 31, 2025
  If water isn't entering your Electrolux washer or is entering slowly, consider these possibilities: * Inadequate water supply in your area. * Water supply faucets not fully open. * Water being used elsewhere in the house. * Kinked water inlet hoses. * Plugged water inlet screens. Try these solutions: * Check another faucet in the house and wait for the water supply and pressure to increase. * Fully open both hot and cold faucets. * Ensure water pressure is at least 30 psi (260 kPa) and avoid running water elsewhere while the washer is filling. * Straighten the hoses. * Clean the screens.
J
John SullivanAug 30, 2025
How to stop Electrolux Washer from oversudsing?
- N
  Nicholas RiveraAug 30, 2025
  If your Electrolux washer is oversudsing, it's likely due to: * Using the wrong detergent. * Using too much detergent. To resolve this: * Run a rinse cycle and use a low-sudsing, high-efficiency detergent in the future. * Run a rinse cycle and use less detergent in future loads.
J
Jennifer MartinAug 29, 2025
What to do if Electrolux Washer makes rattling and clanking noise?
- A
  Andrew WrightAug 29, 2025
  If your Electrolux washer is making rattling and clanking noises, it could be due to: * Foreign objects such as coins or safety pins in the drum or pump. * Belt buckles and metal fasteners hitting the wash drum. To resolve this: * Stop the washer and check the drum. If the noise continues after restarting, objects may be in the pump. * To prevent unnecessary noise and damage to the drum, fasten fasteners and turn items inside out.
G
George SalazarAug 28, 2025
What to do if Electrolux Washer vibrates?
- A
  Austin RiceAug 28, 2025
  If your Electrolux washer is making vibrating noises, it could be due to these reasons: * The washer is not resting firmly on the floor. * The shipping bolts and foam blocks were not removed during installation. * The wash load is unevenly distributed in the drum. Here's how to solve it: * Adjust the leveling legs. * Refer to the Installation Section for removing shipping bolts and foam blocks. * Stop the washer and redistribute the wash load.
M
Maria WestAug 27, 2025
What to do if Electrolux Washer load is too wet after spin?
- K
  Kevin PrestonAug 27, 2025
  If your Electrolux washer leaves the load too wet after spinning, it could be due to the following reasons: * The washer is overloaded. * The load is too small. * The load is out of balance. * The drain hose is kinked. To address this, try the following: * Avoid overloading the washer. * Add one or two similar items to help balance the load. * Rearrange the load to allow proper spinning. * Straighten the drain hose.
C
Christine BrownAug 27, 2025
What to do if Electrolux EWFLW65H Washer leaks?
- D
  dadamsAug 27, 2025
  If your Electrolux washer is leaking, it could be due to a loose fill hose connection at the faucet or washer, or clogged house drain pipes. Check and tighten the hose connections, and install the rubber sealing washers provided. If the drain pipes are clogged, unclog them or contact a plumber if necessary.
D
Dr. Alison BakerAug 25, 2025
Why Electrolux Washer water does not drain?
- T
  Timothy RitterAug 26, 2025
  If the water in your Electrolux washer is not draining or is draining slowly, it is likely because the drain hose is kinked or clogged. Clean and straighten the drain hose. The maximum standpipe height is 8’ (2.4 m).