Why Electrolux EWFLW65H Washer warm or hot water is not hot enough?
A
Amy RobertsonSep 23, 2025
If the warm or hot water in your Electrolux washer isn't hot enough, it could be due to:
* The hot water heater being set too low or located far from the washer.
* Hot water being used elsewhere in the house.
To fix this:
* Measure the hot water temperature at a nearby faucet with a candy or meat thermometer. The water temperature should be at least 120°F (49°C). Adjust the water heater as necessary.
* Avoid using hot water elsewhere before or during washer use. If the problem persists, the hot water system may be unable to support more than one use at a time.
D
Dr. Alison BakerAug 25, 2025
Why Electrolux Washer water does not drain?
T
Timothy RitterAug 26, 2025
If the water in your Electrolux washer is not draining or is draining slowly, it is likely because the drain hose is kinked or clogged. Clean and straighten the drain hose. The maximum standpipe height is 8’ (2.4 m).
C
Christine BrownAug 27, 2025
What to do if Electrolux EWFLW65H Washer leaks?
D
dadamsAug 27, 2025
If your Electrolux washer is leaking, it could be due to a loose fill hose connection at the faucet or washer, or clogged house drain pipes. Check and tighten the hose connections, and install the rubber sealing washers provided. If the drain pipes are clogged, unclog them or contact a plumber if necessary.
M
Maria WestAug 27, 2025
What to do if Electrolux Washer load is too wet after spin?
K
Kevin PrestonAug 27, 2025
If your Electrolux washer leaves the load too wet after spinning, it could be due to the following reasons:
* The washer is overloaded.
* The load is too small.
* The load is out of balance.
* The drain hose is kinked.
To address this, try the following:
* Avoid overloading the washer.
* Add one or two similar items to help balance the load.
* Rearrange the load to allow proper spinning.
* Straighten the drain hose.
B
Beverly BergerSep 23, 2025
Why Electrolux Washer is making a high pitch “jet engine” noise?
K
Kristina DoyleSep 23, 2025
A certain amount of motor whine is normal during the spin cycle of your Electrolux washer. This is normal operation of the unit.
J
james64Nov 22, 2025
Why Electrolux EWFLW65H Washer won't start?
A
Aaron HenryNov 22, 2025
Your Electrolux washer might not be starting due to several reasons:
* The electrical power cord may not be properly plugged in.
* A house fuse might be blown, a circuit breaker tripped, or there could be a power outage.
* The water supply faucets might not be turned on.
* The motor could be overheated.
* The dispenser drawer might not be completely closed.
To resolve this:
* Ensure the plug fits tightly in the wall outlet.
* Reset the circuit breaker or replace the fuse (do not increase fuse capacity). If it's a circuit overload, have it corrected by an electrician. If it's a power outage, contact your local electric company.
* Turn on the water supply faucets.
* If the motor is overheated, it will automatically restart after a cool-down period of up to 30 minutes (i...
V
Victor KennedySep 12, 2025
How to remove pilling from clothes washed in Electrolux Washer?
A
Abigail DiazSep 12, 2025
If you're experiencing pilling (fibers breaking off, balling up, and clinging to the fabric) after washing in your Electrolux washer, keep in mind that pilling is normal with synthetic and permanent press fabrics due to abrasion from normal wear. You can use a lint brush or shaver to remove pills. Use fabric softener in the washer to lubricate fibers. When ironing, use spray starch or fabric finish on collars/cuffs. Turn items inside out to reduce abrasion.
A
andersonelizabethSep 12, 2025
How to remove yellow buildup on synthetic fabrics in Electrolux EWFLW65H Washer?
J
Jason SteeleSep 12, 2025
If you notice a yellow buildup of body soil on synthetic fabrics after washing in your Electrolux washer, it could be due to:
* Agitation time being too short.
* Wash water temperature being too low.
* Not using enough detergent.
To resolve this:
* Soak the items in a detergent booster or a product containing enzymes.
* Wash in hot water (120°F/49°C) using the full permanent press cycle. Increase the amount of detergent and add bleach or treat with a color remover.
G
gabrielle59Sep 5, 2025
How to remove residue or powder on dark items from Electrolux EWFLW65H Washer?
K
Kathryn SmithSep 5, 2025
If you find residue or powder on dark items or notice stiff, harsh fabrics after washing in your Electrolux washer, it could be due to:
* Undissolved detergent.
* Some nonphosphate granular detergents combining with hard water minerals.
* Overloading the washer.
To resolve this:
* Increase the water temperature to the hottest level safe for the fabric.
* Avoid overloading the washer.
* Use liquid detergent, or use a nonprecipitating water conditioner with nonphosphate granular detergent.
J
Jason TannerSep 2, 2025
Why Electrolux EWFLW65H Washer water is entering but tub does not fill?
M
Mark MartinSep 2, 2025
If water is entering your Electrolux washer but the tub is not filling, it is likely that the drain hose standpipe is not at the correct height. The standpipe must be a minimum of 24” (61 cm) high to prevent siphoning. Refer to the Installation Section.
To Next Page
General
