To Next PageTo Next PageWhat to do if Electrolux SKYLINE 6-10-20GN shows error N°292 ASCH?
If your Electrolux oven displays error code N°292 ASCH, it could be due to a dirty air intake filter or a room temperature that is too high. Try cleaning the air intake filter. Also, allow the oven to cool down before cooking. If the warning continues, it is advisable to call service.
What to do if Electrolux SKYLINE 6-10-20GN Oven displays error N°200 ACUM?
If your Electrolux oven shows the error N°200 ACUM, it indicates an issue with the communication cable or connectors between the ACU and UI, a communication cable failure, or an ACU failure. As a first step, switch the appliance off and on. If the warning persists, contact service.
What to do if Electrolux SKYLINE 6-10-20GN displays error N°243 BEtc?
If your Electrolux oven shows error N°243 BEtc, it indicates a mechanical or electrical problem with the vent valve. Call service and continue cooking, but only clean the oven manually until the issue is resolved. If the oven is cleaning, it is not possible to perform or complete the cleaning cycle. To reset the message, switch the oven OFF and then ON again.
How to fix Electrolux SKYLINE 6-10-20GN Oven error N° 110 bAtt?
The Electrolux oven error code N° 110 bAtt indicates that the CR2032 type battery on the UI needs replacement due to ageing. Replace the battery on the UI § U.I LEVEL T,K (TOUCHSCREEN) §U.I LEVEL B,C (DIGIT).
What to do if Electrolux SKYLINE 6-10-20GN shows error N°323 ACF?
If your Electrolux oven displays error N°323 ACF, it means the filter frame is not present or the microswitch AFS is interrupted. To resolve this, refit the filter.
What to do if Electrolux Oven shows error N°116 ACSS?
The Electrolux oven error code N°116 ACSS means that there was a wrong software upload (for example, after replacing the ACU board). Call service to upload the correct software.
What to do if Electrolux SKYLINE 6-10-20GN Oven shows error N°115 ACUS?
The Electrolux oven error code N°115 ACUS means that there was a wrong software upload (for example, after replacing the ACU board). Call service to upload the correct software.
General| Brand | Electrolux |
|---|---|
| Model | SKYLINE OVEN 6-10-20GN |
| Category | Oven |
| Language | English |
Details crucial safety guidelines, precautions, and PPE requirements for safe operation.
Explains the different user interfaces, including touch and digit displays.
Lists available software editions for the electronic boards, categorized by type.
Covers settings and service area for touch screen interfaces, detailing calibration and functions.
Provides access to advanced service functions via password, with a 15-minute active period.
Details how to view and change appliance parameters for touch screen models.
Explains how to check cycle counts, hours used, and reset counters.
Covers managing data transfer between the UI and a USB key for various functions.
Details the procedure for uploading the programming file (P.F.) to update the oven software.
Explains how to upload programming parameters (P.P.) to set factory values or after software updates.
Guides on uploading the PNC & SER file, essential after replacing the user interface board.
Explains how to enter the service area on digit display ovens using button combinations.
Details how to navigate and modify appliance parameters in the service area.
Guides on accessing and viewing various operational counters within the service menu.
Details how to view and interpret the alarm log for troubleshooting.
Explains how to read firmware versions and identification data from the appliance.
Illustrates downloading software packages from the Agelux website.
Describes the user interface for touchscreen models, including connections and communication.
Details the user interface for digit display models, including connections and communication.
Lists and explains various alarms and warnings, including causes and service actions.
Guides on downloading the "KILL_CLEAN" software from the Pride website.
Guides on downloading the "KILL_CLEAN" software from the Agelux website.
Details the procedure for EH2O errors with software version 1.1.0 and higher.
Explains handling EH2O errors for software version 1.0.18, noting it's not a locking error.
Provides the generic electrical wiring diagram for gas appliances.
Provides the generic electrical wiring diagram for electric appliances.
