Elite Screens ezFrame Series - User Manual

Rev.041014-JA www.elitescreens.com 1
ezFrame &
Sable Frame Series
Fixed&Frame&Projection&Screen&
User’s&Guide&
Hardware and Parts List
1. Frame Parts x 6 pcs (4 top/bottom horizontal frame pcs + 2 side vertical frame pcs)
2. Tension Rods x 6 pcs (4 top/bottom rods + 2 side rods)
3. Screen Material x 1 pc
4. Center joints x 2 pcs
5. Elbow Joints x 4 pcs
6. Wall brackets x 2 – 3 pcs (depending on model/size)
7. M5x50 wood screws x 6 pcs
8. Hollow wall anchor x 6 pcs
9. M5x15 screws x 16 pcs
10. Center Support Bar x 1 – 2 pcs (depending on model/size)
11. Support joiner x 2 – 4 pcs (depending on model/size)
12. Fix Plates x 60 – 180 pcs (depending on model/size)
Note: Please make sure all parts are included in your package before proceeding to assemble your Elite
Screens fixed frame projection screen.
FRAME ASSEMBLY
1. Insert the center joint connector into to one of the 1/2 horizontal frames and fasten it with two M5x15 screws.
bevel connection
½ Horizontal Frame
M5×15 screws

Summary

Hardware and Parts List

FRAME ASSEMBLY

Insert Center Joint Connector

Connecting horizontal frame pieces using center joints and screws.

Attaching the screen material to the frame

Attach the fix plates

Securing the screen material using fix plates at corners and sides.

Black backing for AcousticPro models

Center Support Bar

Installation

CAUTION

Overview

1. Function Description
2. Usage Features
3. Assembly
4. Attaching the Screen Material
5. Black Backing for AcousticPro Models
6. Center Support Bar Installation
7. Wall Installation
8. Maintenance Features
9. Safety and Care

This document outlines the assembly, installation, and maintenance of the Elite Screens ezFrame & Sable Frame Series Fixed Frame Projection Screen.

Function Description

The Elite Screens ezFrame & Sable Frame Series is a fixed frame projection screen designed to provide a flat and taut surface for optimal image projection. The fixed frame design ensures a consistently flat viewing surface, which is crucial for high-quality projection without distortions. The screen material is stretched over a rigid aluminum frame, creating tension that eliminates wrinkles and waves, thereby enhancing the clarity and sharpness of projected images. For AcousticPro models, a black backing material is included to prevent light penetration from behind the screen, which could otherwise cause image distortion. This feature is particularly beneficial in setups where there might be objects or light sources behind the screen. The screen is designed for permanent wall mounting, offering a clean and professional aesthetic suitable for home theaters, conference rooms, and other viewing environments.

Usage Features

Assembly:

The assembly process begins with the frame. The frame consists of horizontal and vertical pieces that are joined together using center joint connectors and elbow joints.

1. Horizontal Frame Assembly: Two 1/2 horizontal frame pieces are connected using a center joint connector and secured with M5x15 screws. This process is repeated to assemble a second horizontal frame. It's important not to fully tighten the screws until all frame pieces are assembled to allow for adjustments.
2. Full Frame Assembly: Elbow joint connectors are inserted into the long horizontal frames and fastened with M5x15 screws. The vertical short frames are then inserted into the elbow joints and secured with screws. The exposed ends of the joint connectors are inserted into the short (vertical) frames, and the four corners are aligned to meet at perfect right angles. When joining the frame parts, it is recommended to push simultaneously on the two ends of the long frames to ensure a snug fit.

Attaching the Screen Material:

1. Preparation: The screen material is unrolled and laid face down on a clean, dry, and non-abrasive surface. The frame should also be placed face down on a similar surface.
2. Tension Rod Insertion: Tension rods are inserted separately into the edges of all four corners of the screen material. There are two vertical tension rods and four horizontal tension rods.
3. Centering the Material: The screen material is centered within the assembled frame. It's important to note that the material will appear smaller than the frame; this is intentional, as the material needs to be stretched to achieve the necessary tension for flatness.
4. Attaching Fix Plates: Fix plates are used to secure the screen material to the frame.
   • Corners: The four corners are secured first, following a specific order (A→B→C→D). The first fix plate is placed approximately 10 cm from the frame's corner, and the second fix plate is placed approximately 5 cm away.
   • Stretching and Securing: To attach the material, it is stretched to the corner, and its edge is inserted into the groove of the frame. While one hand holds the material in place, the other hand snaps in the push plate.
   • Sides: After the corners, a fix plate is placed in the center of each side, following the order E→F→G→H.
   • Remaining Fix Plates: Subsequent fix plates are placed in a specific pattern: the next set of fix plates are placed in the middle between the previously installed fix plate and the corner. Then, another set of fix plates is placed between the first and second fix plates and the corner. Finally, the last set of fix plates is installed as shown in the diagram. This process is repeated for all sides to complete attaching the screen material, ensuring even tension across the entire surface.

Black Backing for AcousticPro Models:

For AcousticPro models, a black backing material is used to block light penetration. This backing is held in place by Velcro on the fix plates. Interval markings on the frame indicate the optimal points for inserting the fix plates. The prongs on the fix plates insert into a lip on the back of the frame, creating a friction hold that secures both the acoustic material and the black backing. The backing lies over the back of the white (Acoustic) material and is then held by the Velcro on the fix plates.

Center Support Bar Installation:

For diagonal models 135" and below, one center support bar is used. For models above 135", two center support bars are required.

1. Support Joiner: A support joiner is inserted into each end of the center support bar to complete its assembly.
2. Insertion into Frame: The center support bar is inserted into the upper top groove on the back of the frame (not the groove where the fix plate inserts). The bottom end of the bar is positioned near the approximate center point of the frame, and it is rotated at an angle until both ends align with the groove.
3. Securing: The top end of the bar is slid into the top center point of the frame to complete the installation. This bar provides additional stability to the frame and increases tension on the screen material.

Wall Installation:

1. Location: Use a stud finder to locate the desired installation spot and mark the drill-hole areas.
2. Drilling: Drill holes with the appropriate bit size for the included wood screws.
3. Wall Brackets: Align the wall brackets with the drilled holes and secure them with a Phillips screwdriver. Note that 2 top wall brackets are used for diagonal sizes below 135", and 3 top wall brackets for diagonal sizes 135" and above.
4. Mounting the Screen: Position the fixed frame screen onto the top wall brackets and push down at the center of the bottom frame to secure it. The design of the wall brackets allows the frame to slide over them through its sides, facilitating proper centering.
5. Final Securement: Using both hands, push the lower portion of the fixed frame screen into the lower bracket to complete the installation.

Maintenance Features

Safety and Care:

• Clearance: Ensure that the installation area is free from obstructions such as power switches, outlets, furniture, ladders, or windows that could interfere with the screen.
• Mounting Integrity: Regardless of whether the screen is hung or installed into the wall, verify that proper mounting anchors are used and that the weight is adequately supported by a strong and structurally sound surface. Consulting a home improvement specialist for installation advice is recommended.
• Frame Handling: The frame parts are made of high-quality velour-surfaced aluminum and should be handled with care to prevent damage.
• Protection: When not in use, cover the screen with a furniture sheet to protect it from dirt, grime, paint, or other impurities.
• Cleaning:
  • Frame: Use a damp soft cloth with warm water to remove any marks from the frame.
  • Screen Surface: Use a damp soft cloth with warm water to clean the screen surface.
  • Avoid Harsh Cleaners: Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface, as these can cause damage.
• Damage Prevention: To avoid damaging the screen, refrain from touching it directly with fingers, tools, or any other sharp or abrasive objects.
• Spare Parts: Spare parts should be kept out of reach of small children, adhering to household safety guidelines.

Elite Screens ezFrame Series Specifications