Elkay EZSTL8WSLP User Manual

Page 1 1000002120 (Rev. A- 11/14)
EZSTL8WSLP EZSTL8WSSP LZSTL8WSLP LZSTL8WSSP
*Versatile cooler design allows units to be installed either left-hand high and right-hand low or left-low and right high.
Basin change may be required. See desired rough-in to help determine if the basin change is necessary.
* Versátil diseño refrigerador permite unidades ser instalado o baja alta y derecha izquierda o izquierda baja y alto a la derecha.
Cambio de cuenca puede ser necesario. Ver encastramiento deseado para ayudar a determinar si es necesario el cambio de Cuenca.
* Souples de conception plus frais permet aux unités d’être installé soit faible haute et droite gauche ou gauche basse et haute à droite.
Changement de bassin peut être exigé. Voir désiré rugueux-dans pour aider à déterminer si le changement de bassin est nécessaire.
*Versatile Cooler Model LZSTL8WSSP
alternate installation
*Versátiles instalaciones alternas del
refrigerador Modelo LZSTL8WSSP
*Installations où le refroidisseur
LZSTL8WSSP modèle polyvalente
Amélioré EZ™ & LZ™ Stations de Remplissage de Bouteille Série et Refroidisseurs
Mejorado EZ™ & LZ™ Serie Botella Bombas y Enfriadores
Enhanced EZ
™
& LZ
™
Series Bottle Filling Stations & Coolers
INSTALLATION, CARE & USE MANUAL
Manual de Instalación, Cuidado y Utilización
Manuel d’installation/entretien/utilisation

Elkay EZSTL8WSLP Specifications

General

Product Type	Water Cooler
Material	Stainless Steel
Height	41.5 inches
Filtration	Yes
Mounting Location	Indoor
Power	115V
Number of Basins	1
Drain Included	Yes
Mounting Type	Wall Mount
Finish	Stainless Steel
Bubbler Activation	Push Button

Summary

Elkay EZ and LZ Series Bottle Filling Stations and Coolers Overview

Standard Rough-In: Left-Hand High, Low Bottle Filler Models

Alternate Rough-In: Right-Hand High, Low Bottle Filler Models

Alternate Rough-In: Left-Hand Low, High Bottle Filler Models

Alternate Rough-In: Right-Hand Low, High Bottle Filler Models

Installation Procedures

Hanger Brackets, Trap, and Cooler Installation

Steps for installing hanger brackets, traps, and hanging the cooler unit.

Start Up and Cleaning

Initial operation steps and guidelines for cleaning the unit.

Service Instructions

Lower and Upper Shroud Access

Instructions for removing shrouds to access internal components.

Bubbler Service

Procedure for removing and servicing the bubbler assembly.

Push Bar Switch Mechanism

Explanation of the push bar switch and regulator adjustment.

Bottle Filler Installation

Bottle Filler Plumbing and Electrical Connections

Quick Connect Fittings Operation

WATERSENTRY® Filter Maintenance

Programming Instructions

System Settings: Day/Time, Filter, Refrigeration

Configure date, time, filter status, and refrigeration mode.

Operational Settings: Flow Rate, Temperature, Backlight

Adjust water flow, temperature, and control display backlight.

Energy Saving and Error Management

Manage energy saving features and view/clear error codes.

Troubleshooting Guide

Evaporator and Condenser Component Errors

Troubleshooting issues related to evaporator and condenser thermistors and temperature.

Compressor and Bottle Sensor Errors

Diagnosing compressor cycle issues and bottle sensor obstructions.

Filter and NFC Detection Errors

Resolving water filter status and NFC board detection problems.

115V Parts List

Bottle Filler Replacement Part Kits