What to do if my EMAK Tiller engine doesn't start?
If your EMAK Tiller engine doesn't start or shuts off shortly after starting, there could be a couple of reasons. First, check the spark plug for a spark. If there's no spark, try again with a new spark plug. Second, the engine might be flooded.
Why EMAK Oleo-Mac MH 160 engine doesn't reach full speed?
If your EMAK Tiller engine is not reaching full speed and/or emitting excessive smoke: * The air filter may be dirty. In this case you should clean it following the instructions in the air filter maintenance chapter. * The carburetor may need adjustment. In this case you should contact an Authorized Service Center to adjust the carburetor.
Why is my EMAK Oleo-Mac MH 160 Tiller vibrating so much?
If you are experiencing abnormal vibrations with your EMAK Tiller, it could be due to a couple of issues: * Damaged tools: Replace them. * Loose elements: Tighten them.
Why is my EMAK Oleo-Mac MH 160 Tiller so noisy?
If the EMAK Tiller machine or gearbox is noisy, consider the following: 1. Damaged or loose tools: Secure the tools. 2. Loose protective housings: Tighten the bolts. 3. Poor lubrication: Top up the oil to the correct level.
What to do if EMAK Oleo-Mac MH 160 Tiller won't idle?
If the EMAK Tiller engine starts, runs, and accelerates but won't idle, the carburetor likely needs adjustment. Contact an Authorized Service Center to adjust the carburetor.
Why EMAK Oleo-Mac MH 160 Tiller not accelerating correctly?
If the EMAK Tiller engine starts but doesn't accelerate correctly or doesn't function properly at high speed, the carburetor likely needs adjustment. Contact an Authorized Service Center to adjust the carburetor.
How to prevent EMAK Oleo-Mac MH 160 Tiller tools from breaking?
If the tools of EMAK Tiller are prematurely breaking, it may be due to stony ground. You should do a preventive exploration of the ground.
The cutting mechanism comprising rotating blades.
Warning to keep body parts away from the rotating cutting deck.
Recommends wearing appropriate safety clothing, including protective footwear and eyewear.
Guidance on installing the protective safety guard.
Details on how to properly install the cutting rotors.
Critical safety instructions for handling gasoline and fuel fumes.
Instructions for safe refueling, prohibiting smoking and hot engines.
Specifies the required octane rating and type of gasoline for the engine.
Step-by-step instructions for safely filling the fuel tank.
Explains how altitude affects engine performance and required adjustments.
Provides guidelines for the engine's initial running-in period.
Offers troubleshooting steps for starting issues, including flooded engines.
Explains the function and operation of the machine's control levers.
Warns against removing cut material while the engine is running to prevent injury.
Provides instructions and best practices for operating the motorhoe.
Lists specific uses that are forbidden to ensure safety and prevent damage.
Cautionary note about potential injury from thrown objects when leaning over the guard.
Essential checks to perform before starting the engine.
Critical warning about the cutting attachment not rotating when the engine is idling.
Prohibits operating the machine on public roads.
Warning against using improper methods for lifting the machine.
General safety measures to follow before performing any maintenance.
Prohibits operation of machines that are damaged or improperly assembled.
Emphasizes the use of original or recommended parts for safety and performance.
Critical warning against servicing the machine while the engine is running.
Warns about hot engine components and the risk of burns.
Warning against modifying the carburetor due to emission law violations.
Requirement for authorized service centers for any maintenance not covered in the manual.
Troubleshooting for issues related to engine starting and stalling.
Solutions for problems affecting engine acceleration and high-speed performance.
Guidance for addressing issues of insufficient speed or excessive smoke emission.
Troubleshooting steps for engines failing to maintain a stable idle speed.
Details the warranty period and limitations for private and professional use.
Outlines the specific terms and conditions that govern the warranty.
To Next Page
General
