EasyManuals Logo

Emerson CR202EM8 User Manual

Emerson CR202EM8
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #11 background imageLoading...
Page #11 background image
11
EN
WATCHING TVINTRODUCTION CONNECTION
INITIAL SETTING
OPTIONAL SETTING
TROUBLESHOOTING
INFORMATION
Auto Channel Scan
If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a di erent area after the initial setting, or if you recover the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1
Press [MENU] to display the main menu.
MENU
2
Use [CH K / L] to select “CHANNEL SETUP,
then press [VOL
X
].
e.g.) digital TV mode
or
CH
CH
VOL
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
DTV SETUP
3
Use [CH K / L] to select your desired preset type,
then press [VOL
X
].
e.g.) digital TV mode
or
CH
CH
VOL
- CHANNEL SETUP -
ADD/DELETE(DTV)
AUTO PRESET CH(DTV)
AUTO PRESET CH(TV/DTV)
AUTO PRESET CH(CATV)
! CATV takes approx. 50min.
When aerial antenna is connected, select
AUTO PRESET CH (TV)”, AUTO PRESET CH (DTV)” or
AUTO PRESET CH (TV/DTV)”.
When connected to CATV, select
AUTO PRESET CH (CATV)”.
Scanning and memorizing the channels automatically
start.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
When you selected AUTO PRESET CH (TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
5
Note:
If you connect the cable system directly, contact the CATV
installer.
If you press [POWER] or [MENU] during “AUTO PRESET CH”,
the setting will be canceled.
When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
Channel setting will be saved even if the power fails.
If you have Spanish or French menus and need English, press
[MENU]. Use [CH K / L] to select “IDIOMA” or “LANGAGE”.
Press [VOL X] to select “ENGLISH”. Press [MENU] to remove
the main menu.
With regard only to the digital channel, even after the
scanning is complete if you unplug the AC power cord before
turning off the unit by pressing [POWER], the channel setting
may be lost.
Language Selection
You can choose English, Spanish, or French as your on-screen language.
1
Press [MENU] to display the main menu.
MENU
2
Use [CH K / L] to select “LANGUAGE”,
then press [VOL X] repeatedly to change the setting.
e.g.) digital TV mode
or
CH
CH
VOL
- TV SETUP -
PICTURE
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
DTV SETUP
ENGLISH
ESPAÑOL
FRANÇAIS
3
Press [MENU] to exit.
MENU
5

Table of Contents

Other manuals for Emerson CR202EM8

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Emerson CR202EM8 and is the answer not in the manual?

Emerson CR202EM8 Specifications

General IconGeneral
BrandEmerson
ModelCR202EM8
CategoryCRT TV
LanguageEnglish

Related product manuals