Emerson Rosemount 5300 Series - Page 14

Product Data Sheet
00813-0100-4530, Rev DA
December 2010
Rosemount 5300 Series
14
KJ FISCO - ATEX, FM, IECEX Intrinsic Safety
(10)
KK FISCO - ATEX, CSA, IECEX Intrinsic Safety
(10)
KL FISCO - FM, CSA, IECEX Intrinsic Safety
(10)
Options
Standard Standard
M1 Integral digital display ★
P1 Hydrostatic testing
(11)
★
LS Long stud 9.8 in (250 mm) for flexible single lead probe to prevent contact with wall/nozzle.
Standard height is 3.9 in (100 mm) for probes 5A and 5B; 5.9 in. (150 mm) for probes 6A and 6B
★
T1 Transient Protection Terminal Block (standard with FISCO options) ★
W3 2.2 lb (1 kg) weight for flexible single lead probe (5A). L=5.5 in. (140 mm) ★
Expanded
BR Mounting Bracket for 1.5 in. NPT Process Connection (RA)
(12)
Special Configuration (Software)
Standard Standard
C1 Factory configuration (CDS required with order) ★
C4 Namur alarm and saturation levels, high alarm ★
C5 Namur alarm and saturation levels, low alarm ★
C8 Low alarm
(13)
(standard Rosemount alarm and saturation levels) ★
Special Certifications
Standard Standard
Q4 Calibration Data Certification ★
Q8 Material Traceability Certification per EN 10204 3.1
(14)
★
QS Prior-use certificate of FMEDA Data. Only available with HART 4-20 mA output (output code H). ★
U1 WHG Overfill Approval. Only available with HART 4-20 mA output (output code H) ★
Expanded
QG GOST Primary Verification Certificate
PlantWeb Diagnostic Functionality
Standard Standard
D01 F
OUNDATION fieldbus Diagnostics Suite ★
DA1 HART Diagnostics Suite ★
Remote Housing Mounting
Expanded
B1 1m / 3.2 ft. Remote Housing Mounting Cable and Bracket
B2 2m / 6.5 ft. Remote Housing Mounting Cable and Bracket
B3 3m / 9.8 ft. Remote Housing Mounting Cable and Bracket
(1) Not available with Flame/Explosion-proof approvals (E1, E3, E5, E6, E7, KA, KB, KC, and KD)
(2) Process seal rating. Final rating depends on flange and O-ring selection. See “Tank Connection and Probe” on page 31.
(3) For other materials, consult the factory.
(4) 0.79 lb (0.36 kg) standard weight for flexible single lead probe. L=5.5 in. (140 mm).
(5) Extra length for fastening is added in the factory.
(6) 1.2 lb (0.56 kg) standard weight for flexible single lead probe. L=5.5 in. (140 mm).
(7) Probe weight included if applicable. Give the total probe length in feet and inches or meters and centimeters, depending on selected probe length unit.
If tank height is unknown, please round up to an even length when ordering. Probes can be cut to exact length in field. Maximum allowable length is
determined by process conditions. See “Tank Connection and Probe” on page 31 for more probe length guidance.
(8) Available in 316L SST. For other materials, consult the factory.
(9) Available in 316L and EN 1.4404. For other materials consult the factory.
(10) Requires F
OUNDATION fieldbus signal output (U
i
parameter listed in “Product Certifications” on page 36).
(11) Available for flanged connection.
(12) Only for Standard Temperature and Pressure.
(13) The standard alarm setting is high.
(14) Certificate includes all pressure retaining wetted parts.
Example Model String: 5303-H-A-1-S-1-V-6A-M-025-50-AA-I1-M1C1. E-025-05, means 25 ft and 5 in. probe length. M-025-50, means 25.5 m.
TABLE 2. 5303 Level for Solids Ordering Information
★ The Standard offering represents the most common options. The starred options (★) should be selected for best delivery.
The Expanded offering is subject to additional delivery lead time.