Empire Pro-Finish 6060

Questions and Answers

K
Karen TrujilloAug 16, 2025
What to do if media is escaping from the Empire dust collector?
- L
  Leah RuizAug 16, 2025
  To resolve media escaping from the Empire dust collector into the work area: * Replace leaking or refasten loose bags. * Adjust reclaimer air inlet settings. * Shake the dust bag or dust collector bags. * Replace filters if they are blinded. * Reverse the fan rotation. * Replace media and adjust the reclaimer tuning band if the media has a high dust content. * Remove obstructions from the recovery hose. * Clean the cabinet air inlet with an air line. * Tighten the dust collector door or replace the gasket if it leaks air. * Replace a worn nozzle with the recommended size (maximum ¼” diameter pressure, maximum 7/32” air jet for suction).
K
Katherine RodgersAug 19, 2025
How to improve the production rate of my Empire equipment?
- T
  Tara MooreAug 19, 2025
  If you're experiencing a poor production rate with your Empire equipment, consider the following: * Increase blast air pressure within the specified range if it's too low. * Install a larger nozzle (and air jet on suction systems) if the current one is too small. * Ensure you are using the correct media. * Adjust media flow as needed. * Add media to maintain the recommended level. * Ensure parts are dry and free of oil or grease. * Replace old media with new and adjust the reclaimer tuning band if the media has a high dust content.
S
Steve ReevesAug 22, 2025
What to do if Empire has blast air flow, but intermittent or no media flow?
- C
  carterpaigeAug 22, 2025
  If your Empire blast system has blast air flow, but intermittent or no media flow, consider these solutions: * Adjust and maintain pressure within the recommended range if the blast air pressure is too low. * Disassemble and clean the nozzle if it is clogged. * Remove damp media from the system and replace it with new, dry media. Also, check compressed air supply filters and avoid blasting wet or oily parts.
L
lawrence90Aug 25, 2025
What causes intermittent media flow in my Empire blast system?
- S
  Steven PriceAug 26, 2025
  If your Empire system exhibits blast air flow with intermittent or no media flow (continued), check these points: * For suction systems, ensure the nozzle orifice size is twice the air jet orifice size (e.g., 1/8” diameter air jet requires minimum ¼” diameter nozzle). * For suction systems, adjust the media hose in the media regulator and ensure an airtight seal at the suction gun body. * For suction systems, clear a clogged media hose by blowing air through it. * For pressure systems, adjust the media regulator if it's closed. * For pressure systems, check for and repair compressed air leaks in the sealing plunger or exhaust valve. * For pressure systems, clear any obstruction in the Sure-Flo media regulator.
D
Diane HullAug 28, 2025
How to stop static charge build-up in Empire equipment?
- S
  Sarah DominguezAug 28, 2025
  If you're experiencing static charge build-up and discharge from your Empire equipment, consider the following: * Replace the blast hose with one of high quality if the current one is a poor conductor. * Earth ground the system properly. * Place the part on a metal surface if it's insulated or resting on a rubber mat. * Install an Empire Anti Static Strap, part 510411, if there is low compressed air and ambient humidity.
M
Michele DiazAug 31, 2025
What to do if there is no air or media flow from the Empire nozzle?
- J
  Jody RoweAug 31, 2025
  If there is no air or media flow from the Empire nozzle, make sure that: * All air valves from the compressor are open. * The cabinet doors are tightly closed, sealing the door interlock. * The regulator is adjusted. * The nozzle is disassembled and cleaned. * The door interlock air hose is replaced. If the problem continues, further pneumatic control circuit troubleshooting may be required.
M
Mark GallagherSep 3, 2025
Why won't the blast activate on my Empire system?
- T
  Trevor WilkinsSep 3, 2025
  If the lights and blower are working but the blast will not activate on your Empire system, try the following: * Repair any air leaks. * Verify the main air supply is on and the cabinet is receiving air, and the regulator is set properly. * Check for obvious control air leaks. * Listen for air leaks with the main switch ON and foot treadle pressed. * Check for air leaks between points B and C. * If no air escapes when the foot treadle valve is manually pressed, replace the valve.
C
Christopher HernandezSep 6, 2025
Why is good media being carried to the Empire dust collector?
- D
  Derek DownsSep 6, 2025
  To address good media being carried to the Empire dust collector: * Continue use until a bag “cake” forms (approximately eight hours of operation). * Adjust the tuning band. * Add media to the recommended level if there is insufficient media in the suction hopper. * Adjust the slide gate. * Use more coarse media. * Replace the plunger and/or sealing ring if a worn plunger or sealing ring is leaking air into the reclaimer in pressure systems.
M
Michelle GibsonSep 9, 2025
Why is there a delay in blast activation with my Empire foot treadle?
- A
  Andrew ZimmermanSep 9, 2025
  To address excessive delay between stepping on the foot treadle and blast activation in your Empire system: * Adjust the foot treadle tab if it does not fully press the foot treadle valve plunger. * Check the condition of the control air lines if they are kinked or crimped.
A
Arthur BradySep 12, 2025
How to improve visibility during blasting with Empire equipment?
- S
  sherri53Sep 12, 2025
  To improve visibility during blasting with your Empire equipment, decrease the operating air pressure to within the recommended range if it is too high.