EMS 1304 - Page 12

To Next Page

To Previous Page

Span Filter out:

Span Filter in:

Zero Reflector out:

Zero Reflector in:

Span

Filter

Zero Reflector

Main

Lamp

TTL Bulls-eye

Projection Lens

Retro Reflector

Aperture P

Aperture V

Main Page

Default Chapter2
- Guidelines for User Safety and Equipment Protection2
- Warnings2
- Table of Contents5
Warrantee Registration7
Customer Service8
Custom er Servi Ce9
Claims for Damaged Shipments9
Shipping Discrepancies9
Section 110
Sec Tio N 110
System Description10
- Transmissometer/Retro Reflector10
- Control Unit10
- Optional Air Purge Weather Cover System10
- Alignment System10
- Cabling10
Principle of Operation11
- Normal Mode of Operation11
- Internal Calibration System, Zero Mode11
- Internal Calibration System, Span Mode1011
1304 Opacity Specifications13
Sseeccttiioonn22 11 4415
Installation Considerations15
- Choose an Installation Site15
- Accessibility15
- Environment15
- Stack Exit15
Installation - Mechanical15
- Drawing Notes15
- Sensors Height from Platforms, Walk Way/ Decks, Etc15
- Alignment of Stack Flanges 15 S E16
- Installation Procedure - Stack Flanges16
- Sample Area16
Modbus Communication and Addresses16
- Reading Analog Output Block Addresses:1617
- Reading Discrete Output Block Addresses17
- Writing17
- Communication Menu Has the Following Sub Categories and Default Settings17
- Changing Communication Settings18
- Mounting the Air Plenum and Weather Covers19
Covers20
Mounting the Air Plenum and Weather20
- Transceiver and Retro Reflector Assembly20
- Air Flow Switch22
- Control Unit22
Secti on 323
- C T I O N23
Before Start up23
Stack Exit Correlation Computation2223
Start up Service24
- Verifying Instrument Operation and Configuration24
EDIT Keys24
Factory O.P.L.R. Display24
Quick Menu24
Zero/Span Calibration Check25
Secti on 426
- C T I O N26
Instrument Operations and Adjustments26
- Overview of the Systems Operation26
- Front Panel Led's26
- Fault Messages26
- Control Unit Manual Controls27
- Alarm Set Point Adjustments27
- Alarm Time Delay Adjustment27
- 4-20Ma Outputs28
- Recorder or Other Device Calibration28
- Auto Cal Timer Adjustment29
- Disable Internal Cal Timer29
- Remote Calibration Cycle Initiate29
- Remote Calibration Cycle Acknowledgment2829
Secti on 531
- C T I O N31
Ajustments31
- Clear on Stack Zero and Span Calibration3031
- Zero Reflector Adjustment31
- Span Filter VALUE32
- Record the Zero/Span Values in the Quick Menu32
- Off Stack Zero Calibration33
Secti on 634
C T I O N34
Using the on Line Zero Reflector (Option)34
- Procedure34
- Filter Correction34
- Course Adjustments36
- Micro-Turn Parts List36
- Filter Certification37
Section 738
Section 738
Preventive/Corrective Maintenance3738
- Preventive/Corrective Maintenance Schedule38
- Trouble Shooting41
- Trouble Shooting -Continued42
Spare Parts43
Section 845
Section 845
Drawings45
- EMS 1001 - Mounting under 6' STACK46
- EMS 1002 - Mounting over 6' Stack47
- EMS 1024 - Air Purge/Weather Cover Mech Installation48
- EMS 1078 - PANEL Cut out for 1304 Control Unit49
- EMS 1079 -1304 Control Unit Dimensions50
- EMS 1077 - Terminal Identification 1304 Control Unit51
- EMS 1131 -1304 with Recorder System Wiring52
Purge Blower Electrical and Pressure Information53

EMS 1304 - Page 12

Table of Contents

Related product manuals