Energetics ET 570 - Part List

Part list
NO.
DESCRIPTION Q'TY
NO.
DESCRIPTION Q'TY
1 BASE FRAME 1 54 ALLEN HEAD BOLT M8 * 53mm 2
2 FRONT STABILIZER 1 55 PLASTIC PAD 4
3 FRONT FOOT COVER (L&R) 2 56 M8 NYLOCK NUT 3
4 M8*52mm CARRIAGE BOLT 4 57 PEDAL FORNT COVER(L) 2
5 M8 WASHER (t=1.2) 12 58 PEDAL FORNT COVER( R ) 2
6 M8 SPRING WASHER 22 59 ROUND SCREW FOR ADJHEIGH 2
7 M8 CAP NUT 4 60 M4*16mm SCREW 2
8 REAR STABILIZER 1 61 M5*12mm SCREW 8
9 REAR FOOT COVER 2 62 PEDAL REAR COVER 2
10
CHAIN COVER (L&R) 2 63 M8*15MM HEX HEAD BOLT 2
11
FRONT CHAIN COVER (L&R) 2 64 SENSOR BRACKET 1
12
M8*15mm ALLEN HEAD SCREW 12 65 SENSOR 1
13
COMPUTER LOWER CABLE 1 66 #6-32 12mm SCREW 1
14
COMPUTER UPPER CABLE 1 67 END CAP 1
15
HANDLEBAR POST 1 68 WIRE ROD 1
16
WASHER M8 OD 28mm 4 69 SMALL SPRING 1
17
AXLE SUPPORT 1 70 M8*52MM HEX HEAD BOLT 1
18
HANDLE BAR (L) 1 71 MAGNETIC HOLDER 1
19
HANDLEBAR FOAM GRIPS 2 72 BEARING <6203ZZ> 4
20
HANDLE BAR (R) 1 73 CLIP C17 <ID 15.7mm> 3
21
PEDAL TUBE WELDMENT (L) 1 74 AXLE FOR PULLEY 1
22
CROSS FRAME (R) 1 75 MAGNET 1
23
M8*20mm HEX HEAD BOLT 2 76 PULLEY 1
24
PEDAL TUBE WELDMENT (R) 2 77 SAFE BRACKET 1
25
M8*25mm HEX HEAD BOLT 2 78 M6*18mm SCREW 4
26
SWIVL TUBE 2 79 SPACER SLEEVE 1
27
M8 WASHER CURVE (t=1.2) 4 80 LARGE SPRING 1
28
PEDAL (L) 1 81 SPACER SLEEVE 3
29
WASHER FOR PEDAL 4 82 M6*14mm HEX HEAD SCREW 3
30
M6*55mm CARRIAGE BOLT 4 83 POWER CABLE 1
31
M6 WASHER (t=1.2) 7 84 M3*15mm SCREW 4
32
M6 SPRING WASHER 4 85 BRACKET 1
33
KNOB DAWL 4 86 SPRING BRACKET 1
34
PEDAL (R) 1 87 M6*10mm SCREW 1
35
HAND PULSE UNIT 1 88 FLYWHEEL 1
36
HAND PULSE 2 89 FLYWHEEL AXLE 1
37
SMALL HANDLEBAR FOAM GRIP (UPPER) 1 90 BEARING <6001ZZ> 2
38
SMALL HANDLEBAR 1 91 CLIP C12<ID11.1mm> 2
39
SMALL HANDLEBAR FOAM GRIP (LOWER) 2 92 M10 WASHER (t=1.0) 1
40
MAGNETIC HOLDER BRACKET 1 93 M10 WASHER (t=2.0) 2
41
M6 NYLOCK NUT 4 94 3/8" WH NUT 2
42
GRIPBAR END CAP 2 95 BELT 1
43
COMPUTER 1 96 SCREW M5 * 12 mm 14
44
M5*12mm SCREW 4 97 CROSS FRAME(L) 1
45
ADAPTOR 1 98 TURNING PEDAL (R) 1
46
PLUG AXLE SUPPORT (48.4mm) 2 99 DRIVE WIRE ROD WHEEL 1
47
PLUG AXLE SUPPORT (46mm) 4 100
PIN 1
48
TURNING PLATE COVER
2 101
SERVO MOTOR 1
49
PEDAL FIX BKT 2 102
M8 * 25 mm SCREW 2
50
M16.5 WASHER CURVE (t=0.25) 2 103
TURNING PEDAL (L) 1
51
BUSHING 8 104
SAFE COVER 2
52
HANDLEBAR END CAP 2 105
M10*28mm SCREW 4
53
PEDAL TUBE WELDMENT SHAFT 2 106
TAPER WASHER

M8*

11*T4.5

4