Energetiq EQ-99 Manager User Manual

Explains safety-related terms like warnings, cautions, and notes used in the manual.

Provides crucial warnings about lethal voltages, electrical shock, and user-serviceable parts.

Steps for unpacking the device and connecting it to existing LDLS systems and components.

Details on connecting DC power, I/O cables, and the interlock plug for the instrument.

Instructions for plugging in the AC cord, powering on, and ensuring proper ventilation for the unit.

Guides on connecting the instrument to a computer and installing necessary USB drivers.

Information on using rack mounting kits for installing the EQ-99 Manager in standard 19" racks.

Step-by-step instructions for mounting the shutter assembly onto the Lamp House.

Describes plugging the shutter cable into the EQ-99 Manager to make it ready for use.

Explains the functions of the LDLS On/Off button and the Shutter Open/Close button on the front panel.

Identifies the various connectors and ports located on the rear panel of the EQ-99 Manager.

Details the mini-XLR shutter connector and the HD15 I/O control connector pinouts.

Explains the 12VDC power connector and the 2-pin Phoenix interlock connector.

Describes how to control the lamp output and monitor status using the On/Off button and VFD display.

Explains the icons displayed on the VFD to indicate normal and fault states of the lamp.

Explains how interlock status affects operation and how controller faults are indicated.

Details the manual and exposure modes for controlling the optional shutter.

Describes various trigger modes (Edge, Level, Off) for synchronizing the shutter with external events.

Discusses the maximum shutter cycle rate and how to manually operate the shutter via an access port.

Illustrates shutter operation timing for positive and negative edge trigger modes in manual operation.

Explains how level trigger modes operate based on voltage levels of the input signal.

Shows timing diagrams for positive and negative level trigger modes for the shutter.

Illustrates exposure mode timing and the effects of exceeding the shutter's maximum operating speed.

Instructions on how to enter, navigate, and change settings within the EQ-99 Manager's menu.

Details the available settings like Trigger Mode, Shutter Mode, and Exposure Time with their value ranges.

Lists detailed technical specifications for the EQ-99 Manager, including power, connectors, and environmental limits.

Covers general specifications like indicators, display, computer interface, and physical dimensions.

Explains the command structure follows IEEE-488.2 and how commands must be terminated.

Differentiates between device-independent commands and device-dependent LDLS commands.

Provides a list of commands related to LDLS control, categorized by function.

Explains command syntax, case-insensitivity, optional characters, and parameter separation.

Details how to send multiple commands in a single string using semicolons for efficiency.

Explains the tree-like command structure and how to shorten commands by omitting redundant paths.

Highlights the advantages of the USB interface, such as speed and commonality, for PC connectivity.

Guides on installing USB drivers and how the instrument appears as a virtual serial port.

Specifies the USB connector type and essential interface settings like baud rate and data bits.

Explains the *IDN? command for querying instrument identification details like model, SN, and firmware version.

Describes the *RST command for resetting the instrument to factory defaults and shutting off the output.

Details the BEEP command for setting or querying the beep enable status for audible alerts.

Explains the BRIGHT command for setting and querying the display brightness level.

Describes the DELAY command for introducing delays in command processing.

Details the ERRors? command for querying error codes from the instrument.

Explains the ERRSTR? command for querying errors with string descriptions.

Details the LDLS:COND? command for querying the LDLS condition register.

Describes the LDLS:EVEnt? command for querying the LDLS event register.

Explains how to set and query the exposure time for the shutter.

Details how to set and query the exposure mode for the shutter.

Explains how to turn the lamp output on or off and query its state.

Details how to set and query the lamp runtime in hours.

Explains how to set and query the shutter's initial state on power-up.

Details how to open, close, or trigger the shutter using commands.

Explains how to set and query the trigger mode for the shutter input.

Details commands for setting and querying the message buffer.

Explains how to set and query the display of errors while in remote mode.

Describes the SN? command for querying the instrument's serial number.

Details the TERM command for setting the response terminator characters.

Explains how to query the current response terminator setting.

Details commands for querying the unit's run time and time since the last TIMER? query.

Describes the VER? command for querying the instrument's firmware version.

Lists common error codes, their descriptions, and the likely causes.

Provides instructions on how to clean the EQ-99 Manager using a damp cloth.

Details the type of fuses to use for replacement and when to discontinue use.

Provides contact methods for obtaining service and repair for the EQ-99 Manager.

Outlines the product warranty terms, coverage, and limitations.

Identifies the product type and manufacturer as required for the declaration of conformity.

Lists the relevant EU directives and harmonized standards the product complies with.