Need help?Do you have a question about the Engl Powerball and is the answer not in the manual?
General| Impedance | 4, 8, 16 Ohms |
|---|---|
| Power Output | 100 Watts |
| Type | Tube Amplifier |
| Outputs | Line Out |
| Speaker Output | 2 x 1/4" |
| EQ | Bass, Middle, Treble |
1/4" unbalanced input for connecting your guitar.
Sets input sensitivity and preamp saturation for Main Channel I (Clean & Crunch).
Boosts upper treble range for Clean and Crunch channels.
Boosts low-end range for Main Channel I (Clean & Crunch).
Controls the bass frequencies of the passive EQ for Main Channel I.
Controls the mid-range frequencies of the passive EQ for Main Channel I.
Controls the treble frequencies for the Clean mode of Main Channel I.
Controls the treble frequencies for the Crunch mode of Main Channel I.
Volume control for the Clean channel, influencing the Send level.
Volume control for the Crunch channel, influencing the Send level.
Indicates if power tube V1 shut off due to excessive current.
Indicates if power tube V2 shut off due to excessive current.
Indicates if power tube V3 shut off due to excessive current.
Indicates if power tube V4 shut off due to excessive current.
Shapes high-frequency response in the power amp stage for all channels.
Shapes low-frequency response in the power amp stage for all channels.
Sets input sensitivity and preamp saturation for Main Channel II (Lo & Hi Lead).
Boosts low-end EQ for the Lo Lead channel.
Boosts low-end EQ for the Hi Lead channel.
Controls bass frequencies of the passive EQ for Main Channel II (Lo and Hi Lead).
Mid-range voicing for Main Channel II when 'open' sound style is selected.
Mid-range voicing for Main Channel II when 'focused' sound style is selected.
Controls treble frequencies of the passive EQ for Main Channel II (Lo and Hi Lead).
Volume control for the Lo Lead channel, influencing the Send level.
Volume control for the Hi Lead channel, influencing the Send level.
Selects between looser ('open') and tighter ('focused') mid-range voicings.
Selects between Main Channel I and Main Channel II.
Increases input sensitivity for Clean/Crunch and Lo Lead/Hi Lead channels.
Master volume A for the power amp output.
Master volume B for the power amp output.
Silences the power amp to allow tubes to stay warm.
AC power on/off switch for the amplifier.
Connection for the AC power cord.
Houses the main fuse and a spare fuse.
Stereo jack for footswitch control of Master Volume and Sound Style.
Stereo jack for footswitch control of Channels and Gain boost.
9-pin port for connecting the ENGL Custom Footswitch Z-5.
Adjusts the sensitivity of the noise gate for the lead channel.
Output for connecting an external effects processor.
Input for connecting an external effects processor.
Mix control for the effects loop signal (Dry/Effect blend).
Speaker output for 4-ohm cabinets or two 8-ohm cabinets.
Speaker output for 8-ohm cabinets or two 16-ohm cabinets.
Speaker output for one 16-ohm cabinet.
Connects via stereo 1/4" cord for channel and master volume switching.
Connects via stereo 1/4" cords for MIDI-controlled channel and style switching.
Connects via 9-pin cable for direct access to all channels and functions.
Amplifier output power rating.
List of vacuum tubes used in the amplifier.
Specifications for internal and external fuses.
Maximum power draw of the amplifier.
Physical size of the amplifier head.
Total weight of the amplifier head.
Diagram showing the placement of tubes in the chassis.
Example settings for achieving a crystal clear guitar tone.
Example settings for a powerful crunch guitar tone.
Example settings for a scooped mid-range metal guitar tone.
Example settings for a high-gain, sustained lead guitar tone.
Example settings for a smooth, singing lead guitar tone.
Guidelines for protecting the amplifier from physical damage and ensuring optimal performance.
Essential precautions regarding high volume, tube heat, electrical safety, and servicing.
To Next Page
