To Next PageTo Next Page
What to do if Epson EPL-6200 does not print even with assigned IP address?
If you cannot print even after assigning IP addresses, it could be because the computer's IP address was manually assigned, while the printer's was assigned via Automatic Private IP Addressing (APIPA). To resolve this, assign the printer an IP address within the same segment as the computer. You can use EpsonNet Config and the printer’s control panel for this.
What to do if Epson printers do not appear in Chooser?
If printers do not appear in Chooser, ensure that Ethernet is selected for “Connect via” in the AppleTalk Control Panel and that AppleTalk is active in Chooser. Also, inspect the network equipment, including the hub cable.
What to do if message appears when starting EpsonNet Config: “EpsonNet Config cannot be used because no network is installed.”?
If the message “EpsonNet Config cannot be used because no network is installed” appears, it means that either TCP/IP and IPX/SPX are not installed, or TCP/IP is installed but its IP address is not set correctly. Install the TCP/IP or IPX/SPX protocol, or set a correct IP address for the computer.
How to fix EpsonNet Config when the Model Name and IP Address do not appear in the dialog box?
If the Model Name and IP Address do not appear in the EpsonNet Config dialog box, it may be because a valid IP address is not set. Set a valid IP address, refresh the status from the View menu, and increase the timeout length in the Tool menu (though this may slow down EpsonNet Config).
How to resolve “Could not complete communicating configuration data” message in EpsonNet Config?
If you see the message “Could not complete communicating configuration data” when sending settings, especially when using a dial-up router, run Command Prompt and enter the command: ROUTE ADD [IP address of the network interface] [IP address of the computer]. Replace the bracketed information with the appropriate IP addresses.
What to do if Epson Bonjour/Rendezvous printer setting is overwritten by AppleTalk printer setting?
If the Bonjour/Rendezvous printer setting is overwritten by the AppleTalk setting, it means the same printer was set up with AppleTalk after being set up with Bonjour/Rendezvous. Change the AppleTalk printer name to avoid conflicts with the Bonjour/Rendezvous printer name.
Why I am unable to start EpsonNet Config with Web Browser?
If you cannot start EpsonNet Config with a Web Browser, it's likely because the IP address for the network interface hasn't been set. Set the IP address using EpsonNet Config for Windows or Macintosh, the printer’s control panel, or the arp/ping commands.
How to resolve Epson extra account generated when using dial-up network?
If an extra account is generated when using a dial-up network, it's because NetWare is enabled even if you're not using it. Disable NetWare on the NetWare screen of EpsonNet Config with Web Browser.
What to do if Epson printers on the IPX network do not appear in the EpsonNet Config dialog box?
If printers on the IPX network don't appear in the EpsonNet Config dialog box: - Ensure the printer is turned on. - Verify the printer is in the same segment as the computer with EpsonNet Config (use Search options for other segments). - Log in to the target NetWare server with supervisor privileges from the computer with EpsonNet Config.
What to do if Unable to set the IP address using the Epson arp/ping commands?
If you're unable to set the IP address using the arp/ping commands: - Ensure the network interface is connected to the network and check the network environment. - Confirm that the printer and computer are in the same segment; the printer should not be located beyond the router.
General| Print Technology | Laser |
|---|---|
| Print Speed | 20 ppm |
| Resolution | 1200 x 1200 dpi |
| Connectivity | Parallel, USB |
| Memory | 8 MB |
| Max Memory | 72 MB |
| Media Size | A4, A5, B5, Letter, Legal, Executive |
| Media Weight | 60 - 163 g/m² |
| First Print Out Time | 10 seconds |
| Supported Operating Systems | Windows, Mac OS |
