Epson L375 - User Manual

To Next Page

Start Here

Load paper

1 Make sure the product is not charging ink. Then ﬂip the

feeder guard forward, raise the paper support, and tilt it

backwards slightly.

2 Slide the edge guide to the left.

3 Load paper, glossy or printable side up and short edge

ﬁrst, against the right side of the rear paper feed slot.

4 Slide the edge guide against the paper, but not too tightly,

and ﬂip the feeder guard back.

5 Pull out the output tray and raise the paper stopper.

Read these instructions before using your product.

Unpack

Note: Do not open the ink bottles until you are ready to ﬁll the ink

tanks. The ink bottles are vacuum packed to maintain reliability.

1 Remove all protective materials from the product.

2 Lift up the scanner unit and remove all protective materials

from inside the product.

Caution: Do not touch the ﬂat white cable or the ink tubes and

their translucent cover.

3 Lower the scanner unit.

Fill ink tanks

Note: This product requires careful handling of ink. Wear disposable

gloves and place a sheet of paper under the ink tank unit when you

ﬁll or reﬁll the ink tanks, as ink may splatter. If ink spills, wipe it off

immediately with a damp towel to avoid permanent stains. If ink gets on

your clothes or belongings, it may not come off.

Caution: Keep the ink bottles out of the reach of children and do not

drink the ink.

1 Open the ink tank unit cover, then remove the cap for the

cyan ink tank and attach it to its holder.

2 Unpack the cyan ink bottle.

3 Snap the bottle tip off, then remove the bottle cap.

Carefully remove the protective seal (avoid touching the ink

underneath the seal), then close the bottle cap tightly.

Caution: Be sure to close the bottle cap tightly, or ink may leak.

4 Fill the tank using all of the ink in the bottle.

Note: Refer to the color coded sticker on the ink tank unit cover

to identify the color of each tank.

Caution: Be sure to ﬁll each tank with the correct ink color.

5 Carefully seal the bottle using the reverse side of the bottle

tip for proper disposal.

6 Replace the ink tank cap securely.

7 Repeat the previous steps for the remaining bottles.

8 Close the ink tank unit cover.

9 Connect the power cord to the back of the product and to

an electrical outlet.

Caution: Do not connect to your computer yet.

10 Raise the control panel and turn on the product. Wait for

the

power light to stop ﬂashing.

Note: If all the product lights are ﬂashing, turn off the product

and check that no protective material has been left inside

the product.

Caution: Do not lower the control panel without ﬁrst squeezing

the release bar underneath or you may damage the product.

11 Press the stop button for 3 seconds until the power

light starts ﬂashing, to begin charging the ink. Ink charging

takes approximately 20 minutes. Ink charging is complete

when the

power light stops ﬂashing.

20 minutes

3 seconds

Note: The ink bottles included with the printer are designed

for printer setup and not for resale. After some ink is used for

charging, the rest is available for printing.

Caution: Do not turn off the product or load paper while the

product is charging or you’ll waste ink.

L375

4129504 Rev.0

1-F C

4129504 Rev.0

1-F M

4129504 Rev.0

1-F Y

4129504 Rev.0

1-F K

Need help?

Do you have a question about the Epson L375 and is the answer not in the manual?

Epson L375 Specifications

General

Print Technology	On-demand inkjet (Piezoelectric)
Functions	Print, Scan, Copy
Maximum Print Resolution	5760 x 1440 dpi
Print Speed (Black)	33 ppm
Print Speed (Color)	15 ppm
Scanner Type	Flatbed color image scanner
Scanner Optical Resolution	1200 x 2400 dpi
Ink Tank System	Yes
Dimensions (W x D x H)	482 x 300 x 145 mm
Weight	4.4 kg
Copy Speed (Black)	7.7 ipm
Copy Speed (Color)	3.8 ipm
Connectivity	USB
Paper Handling	100 sheets
Supported Paper Sizes	A4, A5, A6, B5
Ink Bottle Yield (Black)	4, 500 pages
Ink Bottle Yield (Color)	7, 500 pages
Display	No