Install network software
Install the EasyMP
®
Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the online EasyMP Network Projection Operation
Guide (requires an Internet connection). If you don’t see the EasyMP Network
Projection Guide icon, you can install it from the projector CD or go to the
Epson website, as described on the right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control to
switch to the correct image source, if necessary.
•
If you’re using a Windows laptop, press the function key on your keyboard
that lets you display on an external monitor. It may be labeled CRT/LCD or
have an icon such as . You may have to hold down the Fn key while
pressing it (such as Fn + F7). Wait a moment for the display to appear.
•
If you’re using a Mac laptop, open System Preferences and select
Displays. Select the VGA Display or Color LCD option if necessary, then
click the Arrange or Arrangement tab, and select the Mirror Displays
check box.
Where to get help
Manuals
For more information about using the projector, click the icons on your desktop
to access the online manuals (requires an Internet connection). If you don’t
have icons to the manuals, you can install them from the projector CD or go to
the Epson website, as described below.
Telephone support services
To use the EPSON
®
PrivateLine
®
Support service, call (800) 637-7661 and enter
the PIN on the EPSON PrivateLine Support card included with your projector.
This service is available 6 am to 6 pm, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
US: (562) 276-4394, 6 am to 8 pm, Pacific Time, Monday through Friday, and 7 am
to 4 pm, Pacific Time, Saturday
Canada: (905) 709-3839, 6 am to 8 pm, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet support
Visit www.epson.com/support (U.S.) or www.epson.ca/support
(Canada) for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
4
Replace the wireless LAN module stopper and secure it using the screw
you removed.
5
Close the air filter cover.
6
To configure your projector for your wireless network, do one of the
following:
•
If you’re using the optional Quick Wireless Connection USB key, insert
it into the projector’s USB-A port, look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow the on-screen instructions to install the driver, then run your
presentation. For details, see the online User’s Guide.
•
If you’re not using the key, continue with the steps bbelow.
7
Press the Menu button on the remote control, select the Network menu,
and press .
8
Choose Network Configuration and press .
9
Select the Wireless LAN menu and press .
10
Click Quick or Advanced, and enter your network’s SSID.
11
If your network assigns addresses automatically turn on DHCP. If not,
turn off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the button. When you’re finished
entering an address, highlight Return, then press .
12
To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and/or IP Address Display
settings to Off.
13
See “Install network software” for additional instructions.
EPSON, EasyMP, and PowerLite are registered trademarks, and EPSON Exceed Your Vision is a registered
logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2012 Epson America, Inc. 2/12
Printed in XXXXXX CPD-36666
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1
Plug in and turn on the projector.
2
Press the Menu button on the remote control, select the Network menu,
and press .
3
Select Network Configuration and press .
4
Select the Basic menu and press .
5
Select the Projector Name setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
6
Select the Wired LAN menu and press .
7
Choose IP Settings and press .
8
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9
To prevent the IP address from appearing on the network standby screen,
set the IP Address Display setting to Off.
10
When you are finished, select Complete and press , then press
again to save your settings.
11
Press the Menu button to exit the menu system.
12
See “Install network software” for additional instructions.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).
Or you can purchase online at www.epsonstore.com (U.S. sales)
or www.epson.ca (Canadian sales).
To Previous Page
Loading...
